ClearOne comm AP10 Professional Services Group, Technical Support, Sales and Customer Service

Page 6

2	Introduction ~ Unpacking

Professional Services Group

If you need additional information on how to install, set up, or operate your system, please contact us at one of the locations listed below. We welcome and encourage your comments so we can continue to improve our products and serve your needs.

ClearOne Communications ~ 1825 Research Way ~ Salt Lake City, UT 84119

Technical Support

Telephone:	1.800.283.5936 (USA) or 1.801.974.3760
Fax:	1.801.977.0087
E-mail:	tech.support@clearone.com
Web site:	www.clearone.com

Sales and Customer Service

Telephone:	1.800.945.7730 (USA) or 1.801.975.7200
Fax:	1.800.933.5107 (USA) or 1.801.977.0087
E-mail:	sales@clearone.com

ClearOne Communications EuMEA GmbH

Leonhardstr. 16-18, D-90443 Nuremberg, Germany

Telephone:	+49	911 955159-0
Fax:	+49	911 955159-10
E-mail:	global@clearone.com

Product registration

Please register your AP10 online by visiting ClearOne Technical Support at www.clearone.com. When your product is properly registered, ClearOne Communications is better able to serve you should you require technical assistance. Registration information is also used to notify you of upgrades and new product information.

Product returns

All product returns require a return authorization (RA) number. Please contact the Technical Services Group before attempting to return your AP10 unit.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 6

Contents AP10 Telephone Interface Technical Services Group ~ 1-800-283-5936 USA ~ Table of Contents IiiAppendices OperationFeatures IntroductionTechnical Support Professional Services GroupSales and Customer Service ClearOne Communications EuMEA GmbHFront view UnpackingControls and Connections Introduction ~ Controls and ConnectionsAP10 rear-panel connectors Rear viewEquipment placement Before You InstallPower requirements Telephone line requirementsTechnical Services Group ~ 1-800-283-5936 USA ~ Hardware Setup Connect the unitInstallation ~ Hardware Setup Phoenix connectorCreating a G-Link network Binary DIP Switch Address Position Connecting powerDevice ID DIP switch settings Assigning device ID numbersTechnical Services Group ~ 1-800-283-5936 USA ~ DIP Switch Settings Noise burst/auto-adaptReceive boost Auto-disconnect Receive AGCAuto-answer Call progression/loopNoise burst adapt Receive reductionCalibration RingingTransmit level adjustment Receive level adjustmentAuto-adapt Using the AP10 To answer a callTo make and disconnect a call Using the Telco Interface FoundControllers To muteOther telco options Custom control through DB-25 portTechnical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications AppendicesAppendices ~ Appendix B Pinouts Remote connector pinoutAppendix B Pinouts Pin DescriptionAppendix C Serial Commands Set connector pinoutLine connector pinout ConventionsCommand structure ExampleConvention Description Command Function AP10 Serial CommandsAppendices ~ Appendix C Serial Commands Command form Device AACommand form Device Hook Command form Device HookdExample Command form Device LVL CH Command form Device Mute CH ExplanationCommand form Device Terl Return values Command form Device NullCommand form Device TE Return valuesCommand form Device Terle Command form Device UIDCommand form Device VER Appendix D Warranty This Warranty is Void ifAppendices ~ Appendix D Warranty FCC Part 68 Compliance Appendix E ComplianceFCC Part 15 Compliance Usoc Jacks This device uses RJ-11C and RJ21X terminal jacksSafety Information IC ComplianceAppendices ~ Appendix E Compliance Appendix F Block Diagram Acoustic Echo Cancellation AEC GlossaryGlossary Index Index