ClearOne comm AP10 operation manual Iii, Table of Contents

Page 3

iii

AP10 Installation and Operation Manual
Table of Contents
CHAPTER 1: Introduction	.1
Features	.1
Professional Services Group	.2
Product registration	.2
Product returns	.2
Unpacking	.3
Controls and Connections	.3
Front view	.3
Rear view	.4
Before You Install	.5
Power requirements	.5
Telephone line requirements	.5
Equipment placement	.5
Environmental requirements	.5
CHAPTER 2: Installation	.7
Hardware Setup	.7
Connect the unit	.7
Creating a G-Link network	.8
Assigning device ID numbers	.9
Connecting power	.10

CHAPTER 3: Configuration . . . . . . . . . . . . . . . . . . . . . . . .11

DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Noise Burst/Auto-Adapt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Receive Boost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Receive AGC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Auto-Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Auto-Disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Call Progression/Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 3

Contents AP10 Telephone Interface Technical Services Group ~ 1-800-283-5936 USA ~ Iii Table of ContentsOperation AppendicesIntroduction FeaturesClearOne Communications EuMEA GmbH Professional Services GroupSales and Customer Service Technical SupportIntroduction ~ Controls and Connections UnpackingControls and Connections Front viewRear view AP10 rear-panel connectorsTelephone line requirements Before You InstallPower requirements Equipment placementTechnical Services Group ~ 1-800-283-5936 USA ~ Connect the unit Hardware SetupInstallation ~ Hardware Setup Phoenix connectorCreating a G-Link network Assigning device ID numbers Connecting powerDevice ID DIP switch settings Binary DIP Switch Address PositionTechnical Services Group ~ 1-800-283-5936 USA ~ DIP Switch Settings Noise burst/auto-adaptReceive boost Call progression/loop Receive AGCAuto-answer Auto-disconnectRinging Receive reductionCalibration Noise burst adaptTransmit level adjustment Receive level adjustmentAuto-adapt Using the AP10 To answer a callTo make and disconnect a call Found Using the Telco InterfaceCustom control through DB-25 port To muteOther telco options ControllersTechnical Services Group ~ 1-800-283-5936 USA ~ Appendices Appendix a SpecificationsPin Description Remote connector pinoutAppendix B Pinouts Appendices ~ Appendix B PinoutsConventions Set connector pinoutLine connector pinout Appendix C Serial CommandsCommand structure ExampleConvention Description Command form Device AA AP10 Serial CommandsAppendices ~ Appendix C Serial Commands Command FunctionCommand form Device Hook Command form Device HookdExample Command form Device Mute CH Explanation Command form Device LVL CHReturn values Command form Device NullCommand form Device TE Command form Device Terl Return valuesCommand form Device Terle Command form Device UIDCommand form Device VER This Warranty is Void if Appendix D WarrantyAppendices ~ Appendix D Warranty Usoc Jacks This device uses RJ-11C and RJ21X terminal jacks Appendix E ComplianceFCC Part 15 Compliance FCC Part 68 ComplianceSafety Information IC ComplianceAppendices ~ Appendix E Compliance Appendix F Block Diagram Glossary Acoustic Echo Cancellation AECGlossary Index Index