ClearOne comm AP10 Appendix E Compliance, FCC Part 15 Compliance, FCC Part 68 Compliance

Page 34

30

Appendices ~ Appendix E: Compliance

Appendix E: Compliance

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his/her own expense.

Changes or modifications not expressly approved by ClearOne Communications, Inc. could void the user’s authority to operate the equipment.

FCC Part 68 Compliance

FCC Registration Number: FBIUSA-43110-BR-T

Ringer Equivalence Number (REN): 0.6B

A label containing, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment is prominently posted on the top plate, near the rear of the equipment. If requested, this information must be provided to your telephone company.

USOC Jacks: This device uses RJ-11C and RJ21X terminal jacks.

The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to obtain the maximum RENs for the calling area.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice for you to make the necessary modifications in order to maintain uninterrupted service.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 34
Contents AP10 Telephone Interface Technical Services Group ~ 1-800-283-5936 USA ~ Table of Contents IiiAppendices OperationFeatures IntroductionTechnical Support Professional Services GroupSales and Customer Service ClearOne Communications EuMEA GmbHFront view UnpackingControls and Connections Introduction ~ Controls and ConnectionsAP10 rear-panel connectors Rear viewEquipment placement Before You InstallPower requirements Telephone line requirementsTechnical Services Group ~ 1-800-283-5936 USA ~ Hardware Setup Connect the unitPhoenix connector Installation ~ Hardware SetupCreating a G-Link network Binary DIP Switch Address Position Connecting powerDevice ID DIP switch settings Assigning device ID numbersTechnical Services Group ~ 1-800-283-5936 USA ~ Noise burst/auto-adapt DIP Switch SettingsReceive boost Auto-disconnect Receive AGCAuto-answer Call progression/loopNoise burst adapt Receive reductionCalibration RingingReceive level adjustment Transmit level adjustmentAuto-adapt To answer a call Using the AP10To make and disconnect a call Using the Telco Interface FoundControllers To muteOther telco options Custom control through DB-25 portTechnical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications AppendicesAppendices ~ Appendix B Pinouts Remote connector pinoutAppendix B Pinouts Pin DescriptionAppendix C Serial Commands Set connector pinoutLine connector pinout ConventionsExample Command structureConvention Description Command Function AP10 Serial CommandsAppendices ~ Appendix C Serial Commands Command form Device AACommand form Device Hookd Command form Device HookExample Command form Device LVL CH Command form Device Mute CH ExplanationCommand form Device Terl Return values Command form Device NullCommand form Device TE Return valuesCommand form Device UID Command form Device TerleCommand form Device VER Appendix D Warranty This Warranty is Void ifAppendices ~ Appendix D Warranty FCC Part 68 Compliance Appendix E ComplianceFCC Part 15 Compliance Usoc Jacks This device uses RJ-11C and RJ21X terminal jacksIC Compliance Safety InformationAppendices ~ Appendix E Compliance Appendix F Block Diagram Acoustic Echo Cancellation AEC GlossaryGlossary Index Index