Apple CPX3 manual Remote control, Putting batteries, About the remote control signal

Page 11

Remote control

Remote control

Putting batteries

Please set the batteries to the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

1. Holding the hook part of the battery cover, remove it.

2. Align and insert the two AA batteries (HITACHI MAXELL, Part No.LR6

or R6P) according to their plus and minus terminals as indicated in the remote control.

3. Replace the battery cover in the direction of the arrow and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

Make sure the plus and minus terminals are correctly aligned when loading a battery.

Keep a battery away from children and pets.

Do not recharge, short circuit, solder or disassemble a battery.

Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.

If you observe a leakage of a battery, wipe out the flower and then replace a battery. If the flower adheres your body or clothes, rinse well with water immediately.

Obey the local laws on disposing the battery.

About the remote control signal

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front.

The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

30º 30º Approx. 3 m

NOTE • The remote control signal reflected in the screen or the like may be available. If it is difficult to send the signal to the sensor directly, attempt to make the signal reflect.

The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter fluorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

11

Image 11
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Replacing the filter cover for bottom-up use Contents of packageFastening the lens cover 12 HOT Part namesProjector HOTControl panel Remote controlSuspended from the ceiling Setting upArrangement On a horizontal surfaceArrangement Monitor Connecting your devicesVCR/DVD player About Plug-and-Play capability Connecting your devicesSecurity slot Connecting power supplyUsing the security slot Putting batteries Remote controlAbout the remote control signal Using as a simple PC mouse & keyboard Changing the frequency of remote control signalSTANDBY/ON button Power indicator Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal Operating For an Hdmi signal Searching an input signalSelecting an input signal  For a PC signalFocus ring Adjusting the projectors elevatorAdjusting the zoom and focus Auto button Using the automatic adjustment featureAdjusting the position Keystone button Using the magnify featureCorrecting the keystone distortions Blank button Freezing the screenTemporarily blanking the screen Freeze buttonAdvanced Menu Using the menu functionReset button Easy MenuKeystone Picture ModeAspect AutoEasy Menu Strong ó Weak Using the / buttons switches the gamma modePicture Menu Light ó DarkEnter button, the pattern changes as below Using the / buttons switches the color temperature modePicture Menu Color TempSAVE1, SAVE2, SAVE3, SAVE4 MY MemoryLOAD1, LOAD2, LOAD3, LOAD4 Position Image MenuOver Scan Size PhaseAuto Adjust Image MenuColor Space Input MenuProgressive Video NRFrame Lock Input MenuVideo Format HdmiResolution Setup Menu Standby Mode Setup MenuHdmi Audio VolumeAudio Menu AudioBlank Screen MenuMyScreen Screen MenuStart UP Message Capturing error has occurred. Please try againMyScreen registration is finished Test Pattern ó DOT-LINE1 TemplateAllocated to the Template function is pressed  DOT-LINE4 ó DOT-LINE3 ó DOT-LINE2Auto on Option MenuAuto Search Lamp Time Option MenuAuto OFF Fanspeed ServiceMY Button MY SourceFilter Message GhostInformation Factory ResetKEY Lock Remote FreqSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionIf you have forgotten your Password Turning on the MyScreen PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off Description SecurityIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password BOX Setting the Transition Detector offOn next Using the MY Text Password functionWriting the MY Text Displaying the MY TextDescription Turning on the MY Text Password Channel Closed Caption MenuDisplay ModeType number DT00821 Replacing the lamp MaintenanceCase of replacement by yourself LampLamp Lamp warningFilter cover Cleaning the air filterAir filter Type number MU03602Maintenance Internal temperature is rising TroubleshootingThere is no input signal An improper signal is inputRegarding the indicator lamps Shutting the projector down Resetting all settingsRegarding the indicator lamps Input changeover settings are mismatched Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workPlay monitor Color settings are not correctly adjustedColor Space setting is not suitable Not properly adjustedAir filter MU03602 SpecificationsSpecification