Apple CPX3 manual Image Menu, Over Scan, Position

Page 26

IMAGE Menu

IMAGE Menu

From the IMAGE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

Description

 

 

 

Using the ▲/▼ buttons switches the mode for aspect ratio.

 

For a PC signal

 

NORMAL ó 4:3 ó 16:9 ó 16:10 ó REAL

 

For an HDMI signal

 

NORMAL ó 4:3 ó 16:9 ó 16:10 ó 14:9 ó REAL

ASPECT

For a Video signal, s-video signal or component video signal

 

4:3 ó 16:9 ó 16:10 ó 14:9 ó REAL

For no signal

16:10 (fixed)

This item can be selected only for a proper signal.

The NORMAL mode keeps the original aspect ratio setting.

Performing the automatic adjustment initializes the aspect ratio setting.

 

Using the ▲/▼ buttons adjusts the over-scan ratio.

OVER SCAN

Large (It reduces picture) ó Small (It magnifies picture)

• This item can be selected only for a video, s-video and component video signal.

 

• When this adjustment is too large, certain degradation may appear

 

at the frame area of the picture. In such a case, please adjust small.

 

Using the ▲/▼ buttons adjusts the vertical position.

 

Up ó Down

 

Over-adjusting the vertical position may cause noise to appear on the

 

screen. If this occurs please reset the vertical position to the default setting.

V POSITION

Pressing the RESET button when the V POSITION is selected will reset the

V POSITION to the default setting.

 

 

• When this function is performed on a video signal, s-video signal, or

 

component video signal, the range of this adjustment depends on the

 

OVER SCAN (above) setting. It is not possible to adjust when the OVER

 

SCAN is set to 10.

 

Using the ▲/▼ buttons adjusts the horizontal position.

 

Left ó Right

 

Over-adjusting the horizontal position may cause noise to appear on the

 

screen. If this occurs please reset the horizontal position to the default

H POSITION

setting. Pressing the RESET button when the H POSITION is selected will

reset the H POSITION to the default setting.

 

 

• When this function is performed on a video signal, s-video signal, or

 

component video signal, the range of this adjustment depends on the

 

OVER SCAN (above) setting. It is not possible to adjust when the OVER

 

SCAN is set to 10.

26(continued on next page)

Image 26
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Replacing the filter cover for bottom-up use Contents of packageFastening the lens cover HOT Part namesProjector 12 HOTRemote control Control panelOn a horizontal surface Setting upArrangement Suspended from the ceilingArrangement Monitor Connecting your devicesVCR/DVD player Connecting your devices About Plug-and-Play capabilitySecurity slot Connecting power supplyUsing the security slot Putting batteries Remote controlAbout the remote control signal Changing the frequency of remote control signal Using as a simple PC mouse & keyboardTurning off the power Power on/offTurning on the power STANDBY/ON button Power indicatorOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound For a PC signal Searching an input signalSelecting an input signal  For an Hdmi signalFocus ring Adjusting the projectors elevatorAdjusting the zoom and focus Auto button Using the automatic adjustment featureAdjusting the position Keystone button Using the magnify featureCorrecting the keystone distortions Freeze button Freezing the screenTemporarily blanking the screen Blank buttonEasy Menu Using the menu functionReset button Advanced MenuAuto Picture ModeAspect KeystoneEasy Menu Light ó Dark Using the / buttons switches the gamma modePicture Menu Strong ó WeakColor Temp Using the / buttons switches the color temperature modePicture Menu Enter button, the pattern changes as belowSAVE1, SAVE2, SAVE3, SAVE4 MY MemoryLOAD1, LOAD2, LOAD3, LOAD4 Position Image MenuOver Scan Image Menu PhaseAuto Adjust SizeVideo NR Input MenuProgressive Color SpaceHdmi Input MenuVideo Format Frame LockResolution Setup Menu Setup Menu Standby ModeAudio VolumeAudio Menu Hdmi AudioScreen Menu BlankMyScreen Screen MenuStart UP Message Capturing error has occurred. Please try againMyScreen registration is finished DOT-LINE4 ó DOT-LINE3 ó DOT-LINE2 TemplateAllocated to the Template function is pressed  Test Pattern ó DOT-LINE1Auto on Option MenuAuto Search Lamp Time Option MenuAuto OFF MY Source ServiceMY Button FanspeedGhost Filter MessageRemote Freq Factory ResetKEY Lock InformationChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Using the MyScreen Password FunctionIf you have forgotten your Password Setting the PasswordDescription Security Using the PIN Lock FunctionTurning the Password off Registering the PIN CodeTurning Off the PIN Lock Function If you have forgotten your PIN CodeTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off BOXDisplaying the MY Text Using the MY Text Password functionWriting the MY Text On nextDescription Turning on the MY Text Password Mode Closed Caption MenuDisplay ChannelLamp MaintenanceCase of replacement by yourself Type number DT00821 Replacing the lampLamp warning LampType number MU03602 Cleaning the air filterAir filter Filter coverMaintenance An improper signal is input TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Shutting the projector down Resetting all settingsRegarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedSignal cables are not correctly connected Input changeover settings are mismatchedNot properly adjusted Color settings are not correctly adjustedColor Space setting is not suitable Play monitorAir filter MU03602 SpecificationsSpecification