Apple CPX3 manual Power on/off, Turning on the power, Turning off the power, Lens cover

Page 13

Power on/off

Turning on the power

1. Make sure that the POWER indicator turns in steady orange and the lens cover is removed.

2. Press the STANDBY/ON button on the projector or the remote control.

The projection lamp will light up and the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green.

To display the picture, select an input signal according to the section “Selecting an input signal” (15).

Power on/off

STANDBY/ON button POWER indicator

INPUT/LAMP

STANDBY/ON ENTER

MENU TEMP

POWER

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY	FREEZE	PAGE		VOLUME
MAGNIFY	FREEZE		UP	VOLUME
ON
OFF		DOWN
KEYSTONE	MY BUTTON		2	MUTE
	1		2
POSITION				MENU
	ENTER
ESC				RESET

Lens cover

Turning off the power

1. Press the STANDBY/ON button on the projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds.

2. Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3. Attach the lens cover, after the POWER indicator turns in steady orange.

Do not turn the projector on for about 10 minutes after turning it off. Turning the projector on again too soon could shorten the lifetime of some consumable parts of the projector.

WARNING ►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings.

►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

►Remove the power cord for complete separation.

NOTE • Please power on the projector prior to the connected devices. Power off the projector, after all of connected devices are powered off.

•This projector has the function that can make the projector automatically turn on/off. Please refer to the AUTO ON (38) and AUTO OFF (39) items of the OPTION menu.

•Use the shutdown switch (58) only when the projector is not turned off by normal procedure.

13

Image 13

Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content Fastening the lens cover Contents of packageReplacing the filter cover for bottom-up use Projector Part namesHOT 12 HOTControl panel Remote controlArrangement Setting upOn a horizontal surface Suspended from the ceilingArrangement VCR/DVD player Connecting your devicesMonitor About Plug-and-Play capability Connecting your devicesUsing the security slot Connecting power supplySecurity slot About the remote control signal Remote controlPutting batteries Using as a simple PC mouse & keyboard Changing the frequency of remote control signalTurning on the power Power on/offTurning off the power STANDBY/ON button Power indicatorSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signal For a PC signal  For an Hdmi signalAdjusting the zoom and focus Adjusting the projectors elevatorFocus ring Adjusting the position Using the automatic adjustment featureAuto button Correcting the keystone distortions Using the magnify featureKeystone button Temporarily blanking the screen Freezing the screenFreeze button Blank buttonReset button Using the menu functionEasy Menu Advanced MenuAspect Picture ModeAuto KeystoneEasy Menu Picture Menu Using the / buttons switches the gamma modeLight ó Dark Strong ó WeakPicture Menu Using the / buttons switches the color temperature modeColor Temp Enter button, the pattern changes as belowLOAD1, LOAD2, LOAD3, LOAD4 MY MemorySAVE1, SAVE2, SAVE3, SAVE4 Over Scan Image MenuPosition Auto Adjust PhaseImage Menu SizeProgressive Input MenuVideo NR Color SpaceVideo Format Input MenuHdmi Frame LockResolution Setup Menu Standby Mode Setup MenuAudio Menu VolumeAudio Hdmi AudioBlank Screen MenuStart UP Screen MenuMyScreen MyScreen registration is finished Capturing error has occurred. Please try againMessage Allocated to the Template function is pressed  TemplateDOT-LINE4 ó DOT-LINE3 ó DOT-LINE2 Test Pattern ó DOT-LINE1Auto Search Option MenuAuto on Auto OFF Option MenuLamp Time MY Button ServiceMY Source FanspeedFilter Message GhostKEY Lock Factory ResetRemote Freq InformationInputting the Password Using Security FeaturesChanging the Password SecurityIf you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Setting the PasswordTurning the Password off Using the PIN Lock FunctionDescription Security Registering the PIN CodeIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function BOX Setting the Transition Detector offWriting the MY Text Using the MY Text Password functionDisplaying the MY Text On nextDescription Turning on the MY Text Password Display Closed Caption MenuMode ChannelCase of replacement by yourself MaintenanceLamp Type number DT00821 Replacing the lampLamp Lamp warningAir filter Cleaning the air filterType number MU03602 Filter coverMaintenance There is no input signal TroubleshootingAn improper signal is input Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Resetting all settingsShutting the projector down Signal cables are not correctly connected Electrical power cord is not pluggedSignal source does not correctly work Input changeover settings are mismatchedColor Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Play monitorSpecification SpecificationsAir filter MU03602