Apple CPX3 manual Electrical power cord is not plugged, These has not been properly fixed

Page 59

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects

About the phenomenon confused with a machine defect, check and cope with it according to the following table.

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The electrical power cord is not plugged in.

10

 

Correctly connect the power cord.

 

 

 

The main power source has been interrupted during

 

 

operation such as by a power outage (blackout), etc.

10, 13

 

Please disconnect the power plug from the power outlet,

Power does not

and allow the projector to cool down at least 10 minutes,

 

then turn the power on again.

 

come on.

 

 

Either there is no lamp and/or lamp cover, or either

 

 

 

 

of these has not been properly fixed.

 

 

Please turn the power off and disconnect the power plug from

52

 

the power outlet, and allow the projector to cool down at least

 

45 minutes. After the projector has sufficiently cooled down,

 

 

please make confirmation of the attachment state of the lamp

 

 

and lamp cover, and then turn the power on again.

 

 

The signal cables are not correctly connected.

8

 

Correctly connect the connection cables.

 

 

 

Signal source does not correctly work.

–

 

Correctly set up the signal source device by referring to the

Neither sounds

manual of the source device.

 

The input changeover settings are mismatched.

 

nor pictures are

14, 15

outputted.

Select the input signal, and correct the settings.

 

 

The BLANK function for pictures and the MUTE

 

 

function for sounds are working.

40

 

AV Mute may be active. Refer to the item “Sound does not

 

come out” and “No pictures are displayed” on the next page

 

 

to turn off the MUTE and BLANK functions.

 

 

The signal cables are not correctly connected.

8

 

Correctly connect the audio cables.

 

 

 

The MUTE function is working.

14

 

Restore the sound pressing the MUTE or VOLUME button

Sound does not

on the remote control.

 

come out.

The volume is adjusted to an extremely low level.

14

 

Adjust the volume to a higher level using the menu function

 

or the remote control.

 

 

The AUDIO setting is not correct.

32

 

Correctly set the AUDIO in the SETUP menu.

 

 

 

The lens cover is attached.

13

No pictures are

Remove the lens cover.

 

displayed.

The signal cables are not correctly connected.

8

 

Correctly connect the connection cables.

 

 

(continued on next page)

59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Replacing the filter cover for bottom-up use Contents of packageFastening the lens cover 12 HOT Part namesProjector HOTControl panel Remote controlSuspended from the ceiling Setting upArrangement On a horizontal surfaceArrangement Monitor Connecting your devicesVCR/DVD player About Plug-and-Play capability Connecting your devicesSecurity slot Connecting power supplyUsing the security slot Putting batteries Remote controlAbout the remote control signal Using as a simple PC mouse & keyboard Changing the frequency of remote control signalSTANDBY/ON button Power indicator Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal Operating For an Hdmi signal Searching an input signalSelecting an input signal  For a PC signalFocus ring Adjusting the projectors elevatorAdjusting the zoom and focus Auto button Using the automatic adjustment featureAdjusting the position Keystone button Using the magnify featureCorrecting the keystone distortions Blank button Freezing the screenTemporarily blanking the screen Freeze buttonAdvanced Menu Using the menu functionReset button Easy MenuKeystone Picture ModeAspect AutoEasy Menu Strong ó Weak Using the / buttons switches the gamma modePicture Menu Light ó DarkEnter button, the pattern changes as below Using the / buttons switches the color temperature modePicture Menu Color TempSAVE1, SAVE2, SAVE3, SAVE4 MY MemoryLOAD1, LOAD2, LOAD3, LOAD4 Position Image MenuOver Scan Size PhaseAuto Adjust Image MenuColor Space Input MenuProgressive Video NRFrame Lock Input MenuVideo Format HdmiResolution Setup Menu Standby Mode Setup MenuHdmi Audio VolumeAudio Menu AudioBlank Screen MenuMyScreen Screen MenuStart UP Message Capturing error has occurred. Please try againMyScreen registration is finished Test Pattern ó DOT-LINE1 TemplateAllocated to the Template function is pressed  DOT-LINE4 ó DOT-LINE3 ó DOT-LINE2Auto on Option MenuAuto Search Lamp Time Option MenuAuto OFF Fanspeed ServiceMY Button MY SourceFilter Message GhostInformation Factory ResetKEY Lock Remote FreqSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionIf you have forgotten your Password Turning on the MyScreen PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off Description SecurityIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password BOX Setting the Transition Detector offOn next Using the MY Text Password functionWriting the MY Text Displaying the MY TextDescription Turning on the MY Text Password Channel Closed Caption MenuDisplay ModeType number DT00821 Replacing the lamp MaintenanceCase of replacement by yourself LampLamp Lamp warningFilter cover Cleaning the air filterAir filter Type number MU03602Maintenance Internal temperature is rising TroubleshootingThere is no input signal An improper signal is inputRegarding the indicator lamps Shutting the projector down Resetting all settingsRegarding the indicator lamps Input changeover settings are mismatched Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workPlay monitor Color settings are not correctly adjustedColor Space setting is not suitable Not properly adjustedAir filter MU03602 SpecificationsSpecification
Top Page Image Contents