Apple CPX3 Shutting the projector down, Resetting all settings, Regarding the indicator lamps

Page 58

Troubleshooting

Regarding the indicator lamps (continued)

POWER

LAMP

TEMP

Description

indicator

indicator

indicator

 

 

 

 

 

 

 

 

There is a possibility that the interior portion

 

 

 

has become heated.

 

 

 

Please turn the power off, and allow the projector to

Blinking

 

 

cool down at least 20 minutes. After the projector has

 

 

sufficiently cooled down, please make confirmation of

In Red

 

 

Turned

Lighting

the following items, and then turn the power on again.

or

off

In Red

• Is there blockage of the air passage aperture?

Lighting

 

 

• Is the air filter dirty?

In Red

 

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

please set FAN SPEED of the SERVICE item in the

 

 

 

OPTION menu to HIGH.

 

 

 

It is time to clean the air filter.

 

 

 

Please immediately turn the power off, and clean or

Lighting

Simultaneous

change the air filter referring to the section “Air Filter”.

In Green

blinking in Red

After cleaning or changing the air filter, please be sure

 

 

 

to reset the filter timer.

 

 

 

After the remedy, reset the power to ON.

 

 

 

There is a possibility that the interior portion

Lighting

Alternative

has become overcooled.

Please use the unit within the usage temperature

In Green

blinking in Red

parameters (5°C to 35°C).

 

 

 

 

 

 

After the treatment, reset the power to ON.

NOTE • When the interior portion has become overheated, for safety purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

Shutting the projector down

Only when the projector can not be turned off by usual procedure (13), please push the shutdown switch using a pin or similar, and disconnect the power plug from the power outlet. Before turning it on again, wait at least 10 minutes to make the projector cool down enough.

Resetting all settings

COMPUTER IN1 COMPUTER IN2

Shutdown switch

When it is hard to correct some wrong settings, the FACTORY RESET function of the SERVICE item in the OPTION menu (42) can reset all settings(except LANGUAGE, FILTER TIME, LAMP TIME, FILTER MESSAGE and etc.) to the factory default.

58

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content Fastening the lens cover Contents of packageReplacing the filter cover for bottom-up use HOT Part namesProjector 12 HOTRemote control Control panelOn a horizontal surface Setting upArrangement Suspended from the ceilingArrangement VCR/DVD player Connecting your devicesMonitor Connecting your devices About Plug-and-Play capabilityUsing the security slot Connecting power supplySecurity slot About the remote control signal Remote controlPutting batteries Changing the frequency of remote control signal Using as a simple PC mouse & keyboardTurning off the power Power on/offTurning on the power STANDBY/ON button Power indicatorOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound For a PC signal Searching an input signalSelecting an input signal  For an Hdmi signalAdjusting the zoom and focus Adjusting the projectors elevatorFocus ring Adjusting the position Using the automatic adjustment featureAuto button Correcting the keystone distortions Using the magnify featureKeystone button Freeze button Freezing the screenTemporarily blanking the screen Blank buttonEasy Menu Using the menu functionReset button Advanced MenuAuto Picture ModeAspect KeystoneEasy Menu Light ó Dark Using the / buttons switches the gamma modePicture Menu Strong ó WeakColor Temp Using the / buttons switches the color temperature modePicture Menu Enter button, the pattern changes as belowLOAD1, LOAD2, LOAD3, LOAD4 MY MemorySAVE1, SAVE2, SAVE3, SAVE4 Over Scan Image MenuPosition Image Menu PhaseAuto Adjust SizeVideo NR Input MenuProgressive Color SpaceHdmi Input MenuVideo Format Frame LockResolution Setup Menu Setup Menu Standby ModeAudio VolumeAudio Menu Hdmi AudioScreen Menu BlankStart UP Screen MenuMyScreen MyScreen registration is finished Capturing error has occurred. Please try againMessage DOT-LINE4 ó DOT-LINE3 ó DOT-LINE2 TemplateAllocated to the Template function is pressed  Test Pattern ó DOT-LINE1Auto Search Option MenuAuto on Auto OFF Option MenuLamp Time MY Source ServiceMY Button FanspeedGhost Filter MessageRemote Freq Factory ResetKEY Lock InformationChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Using the MyScreen Password FunctionIf you have forgotten your Password Setting the PasswordDescription Security Using the PIN Lock FunctionTurning the Password off Registering the PIN CodeTurning Off the PIN Lock Function If you have forgotten your PIN CodeSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off BOXDisplaying the MY Text Using the MY Text Password functionWriting the MY Text On nextDescription Turning on the MY Text Password Mode Closed Caption MenuDisplay ChannelLamp MaintenanceCase of replacement by yourself Type number DT00821 Replacing the lampLamp warning LampType number MU03602 Cleaning the air filterAir filter Filter coverMaintenance An improper signal is input TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Resetting all settingsShutting the projector down Signal source does not correctly work Electrical power cord is not pluggedSignal cables are not correctly connected Input changeover settings are mismatchedNot properly adjusted Color settings are not correctly adjustedColor Space setting is not suitable Play monitorSpecification SpecificationsAir filter MU03602
Top Page Image Contents