Apple CPX3 manual Lamp warning

Page 53

Maintenance

Lamp (continued)

Lamp warning

HIGH VOLTAGE

 

HIGH TEMPERATURE

HIGH PRESSURE

WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

►About disposal of a lamp: This product contains a mercury lamp; do not put it in a trash. Dispose of it in accordance with environmental laws.

•For lamp recycling, go to www.lamprecycle.org. (in the US).

•For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

Disconnect • If the lamp should break (it will make a loud bang when it does),

the plug

ventilate the room well, and make sure not to breathe the gas that

from the

comes out of the projector vents, or get it in your eyes or mouth.

power

• Before replacing the lamp, turn the projector off and unplug the power

outlet

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

 

Handling the lamp while hot can cause burns, as well as damaging the

 

lamp.

•Never unscrew except the appointed (marked by an arrow) screws.

•Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

•Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

•Use only the lamp of the specified type.

•If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

•Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

•Using the lamp for long periods of time, could cause it dark, not to light up or to burst. When the pictures appear dark, or when the color tone is poor, please replace the lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Replacing the filter cover for bottom-up use Contents of packageFastening the lens cover Projector Part namesHOT 12 HOTControl panel Remote controlArrangement Setting upOn a horizontal surface Suspended from the ceilingArrangement Monitor Connecting your devicesVCR/DVD player About Plug-and-Play capability Connecting your devicesSecurity slot Connecting power supplyUsing the security slot Putting batteries Remote controlAbout the remote control signal Using as a simple PC mouse & keyboard Changing the frequency of remote control signalTurning on the power Power on/offTurning off the power STANDBY/ON button Power indicatorSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signal For a PC signal  For an Hdmi signalFocus ring Adjusting the projectors elevatorAdjusting the zoom and focus Auto button Using the automatic adjustment featureAdjusting the position Keystone button Using the magnify featureCorrecting the keystone distortions Temporarily blanking the screen Freezing the screenFreeze button Blank buttonReset button Using the menu functionEasy Menu Advanced MenuAspect Picture ModeAuto KeystoneEasy Menu Picture Menu Using the / buttons switches the gamma modeLight ó Dark Strong ó WeakPicture Menu Using the / buttons switches the color temperature modeColor Temp Enter button, the pattern changes as belowSAVE1, SAVE2, SAVE3, SAVE4 MY MemoryLOAD1, LOAD2, LOAD3, LOAD4 Position Image MenuOver Scan Auto Adjust PhaseImage Menu SizeProgressive Input MenuVideo NR Color SpaceVideo Format Input MenuHdmi Frame LockResolution Setup Menu Standby Mode Setup MenuAudio Menu VolumeAudio Hdmi AudioBlank Screen MenuMyScreen Screen MenuStart UP Message Capturing error has occurred. Please try againMyScreen registration is finished Allocated to the Template function is pressed  TemplateDOT-LINE4 ó DOT-LINE3 ó DOT-LINE2 Test Pattern ó DOT-LINE1Auto on Option MenuAuto Search Lamp Time Option MenuAuto OFF MY Button ServiceMY Source FanspeedFilter Message GhostKEY Lock Factory ResetRemote Freq InformationInputting the Password Using Security FeaturesChanging the Password SecurityIf you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Setting the PasswordTurning the Password off Using the PIN Lock FunctionDescription Security Registering the PIN CodeIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password BOX Setting the Transition Detector offWriting the MY Text Using the MY Text Password functionDisplaying the MY Text On nextDescription Turning on the MY Text Password Display Closed Caption MenuMode ChannelCase of replacement by yourself MaintenanceLamp Type number DT00821 Replacing the lampLamp Lamp warningAir filter Cleaning the air filterType number MU03602 Filter coverMaintenance There is no input signal TroubleshootingAn improper signal is input Internal temperature is risingRegarding the indicator lamps Shutting the projector down Resetting all settingsRegarding the indicator lamps Signal cables are not correctly connected Electrical power cord is not pluggedSignal source does not correctly work Input changeover settings are mismatchedColor Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Play monitorAir filter MU03602 SpecificationsSpecification
Top Page Image Contents