BenQ W6500 user manual Connecting component-video devices, Connecting S-Video or video devices

Page 18

English

Connecting component-video devices

Be sure to match the corresponding colors between the cables and the terminals. The RCA type component video jacks are provided for connection to video output devices. You should also connect the separate audio cable to a suitable audio amplifier.

AV equipment: DVD player,
digital tuner, etc.	From audio output	To audio input
	From audio output	To audio input
	terminals	terminals

Component video cable

Connecting S-Video or video devices

You need only connect S-Video or composite Video cable from the same device, never both at the same time. You should also connect the separate audio cable to a suitable audio amplifier.

AV equipment	From audio	To audio input
	output terminals	terminals

S-Video cable

or

Video cable

• If you have already made a Component Video connection between the projector and the video source device, you need not connect to this device again using an S-Video or composite Video connection as this makes an unnecessary second connection of poorer picture quality. You need only connect using a composite Video connection if both Component Video and S-Video are not supplied on the video source device (for example, with some analog video cameras).

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, please check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

18 Connecting with video equipment

Image 18

Contents Welcome W6000/W6500 Digital Projector Home Cinema SeriesTable of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewRemote control batteries Remote control operationCeiling mounting the projector Projector features Rear view Projector exterior viewFront and upper side view Under viewControl panel Test Remote controlPicture window control keys PIP, Size InfoCeiling Front Choosing a locationFloor Front Floor RearObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenLens Installation for a 43 ratio screenHighest Height HShifting the projection lens To use the lens shift leverReference Picture quality Connecting Hdmi devicesPreparations ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on PreparationsAdjust the projected picture to the size that Fine-tuning the image size and clarityUsing the OSD menu You need using the zoom ring RingUse / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password To leave the OSD menu, press MenuDisabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Two parallel sidesFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To fine-tune the picture modePress to highlight Load Settings From Setting the User 1/User 2/User 3 modeResetting the picture mode To reset the picture mode to the preset factory valuesFine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To set a preferred color temperatureSetting Film Mode To adjust and store the settingsColor Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Aspect ratio Aspect ratio image Using Panamorph lenses optionalImage Using the entire resolution 169 displayTo activate High Altitude Mode Operating in a high altitude environmentHighlight PIP and press / to select On To display the PIP window Using the remote controlDisplaying more than one image source simultaneously PIP function is effective at below source combinationsTurning the projector off Personalizing the projector menu displayLocking control keys To lock the keysOn-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup SetupInformation Resolution Picture -- Basic menu Picture -- Advanced menuFunction Description System Setup menu Display menuLamp Power Normal Menu SettingsAdvanced Setup menu Reset Lamp TimerInformation menu Care of the projector Cleaning the lensCleaning the projector case Storing the projectorLamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message Remove the lamp cover Resetting the lamp timer Power IndicatorsPower Temp Lamp Status & Description Lamp Status & DescriptionTroubleshooting Problem Cause RemedyElectrical SpecificationsOptical TerminalsDimensions Ceiling mount installationMm x 317 mm x 145 mm W x D x H Supported timing for PC input Timing chartFormat Resolution Refresh rate Frequency KHz MHzSupported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsWarranty CopyrightDisclaimer MIC statement FCC statement for United States usersEEC statement for European users Weee directiveEnglish