BenQ W6500 user manual Turning the projector on, Preparations

Page 20

English

Using the projector

Preparations

1. Plug in and turn all of the connected equipment on.

2. If not already in, plug the supplied power cable into the AC inlet on the rear of the projector.

3. Plug the power cable into a wall power outlet and turn the wall switch on.

Turning the projector on

Follow the steps below.

1. Make sure the Power light is orange after power has been applied.

2. Press and hold POWER ON ( II ) on the projector or remote control to turn the projector on.

3. The fans will start operating, and a start-up image displays on the screen for a few seconds while it warms up.

The projector will not respond to further commands while it is warming up.

4.If you are prompted for a password, press the arrow keys to enter a six-digit password. See "Utilizing the password function" on page 23 for details.

5."Source Searching..." will be displayed on the screen before the projector identifies the input source. This message will remain on the screen until a valid signal is detected. See "Selecting an input source" on page 21 for details.

6.If the horizontal frequency of the input source exceeds the range of the projector, the message "No Signal" will be displayed on the screen. This message will remain on-screen until you change the input source to an appropriate one.

20 Using the projector

Image 20

Contents Welcome W6000/W6500 Digital Projector Home Cinema SeriesTable of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Shipping contents OverviewCeiling mounting the projector Remote control batteriesRemote control operation Projector features Projector exterior view Front and upper side viewRear view Under viewControl panel Remote control Picture window control keys PIP, SizeTest InfoChoosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsReference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on PreparationsFine-tuning the image size and clarity Using the OSD menuAdjust the projected picture to the size that You need using the zoom ring RingUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MenuEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Two parallel sidesUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To fine-tune the picture modeSetting the User 1/User 2/User 3 mode Resetting the picture modePress to highlight Load Settings From To reset the picture mode to the preset factory valuesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureColor Management Setting Film ModeTo adjust and store the settings About the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayTo activate High Altitude Mode Operating in a high altitude environmentTo display the PIP window Using the remote control Displaying more than one image source simultaneouslyHighlight PIP and press / to select On PIP function is effective at below source combinationsPersonalizing the projector menu display Locking control keysTurning the projector off To lock the keysMain menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Information Resolution System SetupSetup Function Description Picture -- Basic menuPicture -- Advanced menu System Setup menu Display menuMenu Settings Advanced Setup menuLamp Power Normal Reset Lamp TimerInformation menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Power as Economic Setting Auto OffLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Remove the lamp cover Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionPower Lamp Status & DescriptionTroubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsMm x 317 mm x 145 mm W x D x H DimensionsCeiling mount installation Timing chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsDisclaimer WarrantyCopyright FCC statement for United States users EEC statement for European usersMIC statement Weee directiveEnglish