BenQ W6500 user manual Selecting the aspect ratio, Setting 3D Comb Filter, About the aspect ratio

Page 32

English

Setting 3D Comb Filter

This feature separates composite signal to Y (brightness) signal and C (color) signal, and can help produce clearer and sharper images with correct colors in place.

This function is only available when a Video signal is selected

Selecting the aspect ratio

Picture -- Advanced

Black Level

0 IRE

Clarity Control

 

Color Temperature

Normal

Color Temperature User_ Fine Tuning

2.4

Gamma Selection

Brilliant Color

On

Color Management

 

Film Mode

On

3D Comb Filter

On

Dynamic Black

On

S-Video

EXIT Back

The "aspect ratio" is the ratio of the image width to the image height. Digital TV is usually in 16:9 ratio, which is the default for this projector, and most analog TV signals and DVDs are in 4:3 ratio.

With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input source. Images can be stretched in a linear manner so the whole of the image is stretched equally, or non-linearly, which distorts the image.

To change the projected picture ratio (no matter what aspect the source is):

•Using the remote control

Press one of the aspect ratio keys to suit the format of the video signal and your display requirements.

•Using the OSD menu

1.Press MENU and then press / until the Display menu is highlighted.

2.Press to highlight Aspect Ratio.

3.Press / to select an aspect ratio to suit the format of the video signal and your display requirements.

Display

Aspect Ratio

Anamorphic

Keystone

 

Position

 

Overscan Adjustment

0

PIP

PC & Component YPbPr Tuning

About the aspect ratio

1.Anamorphic (ANA): Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio. This setting stretches and resizes linearly, except that it treats the vertical and horizontal dimensions independently. It stretches the height of the source image until it reaches the full projected height, and stretches the width of the source image until it reaches the full projected width. This may alter the projected aspect, depending upon the original aspect of the source image. Anamorphic is most suitable for images which are already in a 16:9 aspect, like high definition TV, as it displays them without aspect alteration.

2.4:3: Scales a picture so that it is displayed in the center of the screen with a 4:3 aspect ratio. This is most suitable for 4:3 pictures like computer monitors, standard definition TV and 4:3 aspect DVD movies, as it displays them without aspect alteration.

S-Video

 

 

EXIT Back

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16:9 picture

4:3 picture

32 Using the projector

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Welcome W6000/W6500 Digital Projector Home Cinema SeriesTable of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Shipping contents OverviewCeiling mounting the projector Remote control batteriesRemote control operation Projector features Projector exterior view Front and upper side viewRear view Under viewControl panel Remote control Picture window control keys PIP, SizeTest InfoChoosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsReference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on PreparationsFine-tuning the image size and clarity Using the OSD menuAdjust the projected picture to the size that You need using the zoom ring RingUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MenuEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Two parallel sidesUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To fine-tune the picture modeSetting the User 1/User 2/User 3 mode Resetting the picture modePress to highlight Load Settings From To reset the picture mode to the preset factory valuesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureColor Management Setting Film ModeTo adjust and store the settings About the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayTo activate High Altitude Mode Operating in a high altitude environmentTo display the PIP window Using the remote control Displaying more than one image source simultaneouslyHighlight PIP and press / to select On PIP function is effective at below source combinationsPersonalizing the projector menu display Locking control keysTurning the projector off To lock the keysMain menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Information Resolution System SetupSetup Function Description Picture -- Basic menuPicture -- Advanced menu System Setup menu Display menuMenu Settings Advanced Setup menuLamp Power Normal Reset Lamp TimerInformation menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Power as Economic Setting Auto OffLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Remove the lamp cover Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionPower Lamp Status & DescriptionTroubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsMm x 317 mm x 145 mm W x D x H DimensionsCeiling mount installation Timing chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsDisclaimer WarrantyCopyright FCC statement for United States users EEC statement for European usersMIC statement Weee directiveEnglish
Top Page Image Contents