BenQ W6500 Selecting an input source, Fine-tuning the image size and clarity, Using the OSD menu

Page 21

Selecting an input source

The projector can be connected to multiple equipment at the same time. When the projector is first turned on, it will attempt to reconnect with the input source which was in use when the projector was last shut down.

To select the video source:

•Using the remote control or projector

Press one of the Source keys on the remote control, or press SOURCE on the projector repeatedly until your desired signal is selected.

•Using the OSD menu

1.Press MENU and then press / until the System Setup menu is highlighted.

2.Press to highlight Input Source and press ENTER. The source selection bar displays.

3.Press / repeatedly until your desired signal is selected and press

ENTER.

Once detected, the selected source information will display on the screen for seconds. If there are multiple pieces of equipment connected to the projector, you can go back to the source selection bar again to search for other signals.

•If you want the projector to automatically search for the signals, select On in the System Setup > Auto Source Search menu.

•If you want to use the PIP function, see "Displaying more than one image source simultaneously" on page 35 for details.

System Setup

Language	English
Splash Screen	BenQ
Projector Position	Floor Front
Auto Off	Disable
Sleep Timer	Disable
Background Color	Blue
Menu Settings
Input Source	ENTER
Auto Source Search	On
S-Video	EXIT Back
	NOTE: When
	automatically
	searching for a
	valid input
	source, the
	projector cycles
	through the
	available signals
	following the
	sequence from
	top to bottom as
	the source
	selection bar
	shows.

English

Fine-tuning the image size and clarity

1. Adjust the projected picture to the size that

2. Sharpen the picture by rotating the focus

you need using the zoom ring.

ring.

Using the projector

21

Image 21

Contents W6000/W6500 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contentsRemote control batteries Remote control operationCeiling mounting the projector Projector features Front and upper side view Projector exterior viewRear view Under viewControl panel Picture window control keys PIP, Size Remote controlTest InfoFloor Front Choosing a locationCeiling Front Floor RearDetermine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeInstallation for a 169 ratio screen Projection dimensionsHighest Installation for a 43 ratio screenLens Height HTo use the lens shift lever Shifting the projection lensPreparations Connecting Hdmi devicesReference Picture quality ComponentConnecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerPreparations Turning the projector onUsing the OSD menu Fine-tuning the image size and clarityAdjust the projected picture to the size that You need using the zoom ring RingUsing a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password To leave the OSD menu, press MenuChanging the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Two parallel sidesSelecting a preset mode Using the preset and user modesFine-tuning the selected picture mode To fine-tune the picture modeResetting the picture mode Setting the User 1/User 2/User 3 modePress to highlight Load Settings From To reset the picture mode to the preset factory valuesFine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image claritySelecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To set a preferred color temperatureSetting Film Mode To adjust and store the settingsColor Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Image Using the entire resolution Using Panamorph lenses optionalAspect ratio Aspect ratio image 169 displayOperating in a high altitude environment To activate High Altitude ModeDisplaying more than one image source simultaneously To display the PIP window Using the remote controlHighlight PIP and press / to select On PIP function is effective at below source combinationsLocking control keys Personalizing the projector menu displayTurning the projector off To lock the keysOn-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup SetupInformation Resolution Picture -- Basic menu Picture -- Advanced menuFunction Description Display menu System Setup menuAdvanced Setup menu Menu SettingsLamp Power Normal Reset Lamp TimerInformation menu Cleaning the projector case Cleaning the lensCare of the projector Storing the projectorSetting Auto Off Setting Lamp Power as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message Remove the lamp cover Resetting the lamp timer Power Temp Lamp Status & Description IndicatorsPower Lamp Status & DescriptionProblem Cause Remedy TroubleshootingOptical SpecificationsElectrical TerminalsDimensions Ceiling mount installationMm x 317 mm x 145 mm W x D x H Format Resolution Refresh rate Frequency Timing chartSupported timing for PC input KHz MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsWarranty CopyrightDisclaimer EEC statement for European users FCC statement for United States usersMIC statement Weee directiveEnglish