BenQ W6500 user manual System Setup, Information Resolution

Page 38

English

	Language
	Language



	Splash Screen		BenQ/Blue/Black

	Projector Position		Floor Front/Ceiling Front/Floor Rear/Ceiling
	Projector Position		Rear
			Rear
	Auto Off		Disable/5 min/10 min/15 min/20 min/25 min/
System Setup	Auto Off		30 min
			30 min
	Sleep Timer		Disable/30 min/60 min/90 min/120 min/150
			Disable/30 min/60 min/90 min/120 min/150
			min/180 min
			min/180 min

	Background Color		Black/Purple/Blue

		Menu Display Time	5 sec/10 sec/15 sec/20 sec/25 sec/30 sec
	Menu Settings
	Menu Settings	Menu Position	Center/Top-Left/Top-Right/Bottom-Right/
		Menu Position	Bottom-Left
			Bottom-Left
	Input Source		HDMI 1/HDMI 2/Video/S-Video/Component 1/
	Input Source		Component 2/PC
			Component 2/PC
	Auto Source Search		On/Off

		Lamp Power	Normal/Economic
	Lamp Settings
	Lamp Settings	Reset Lamp Timer

		Equivalent Lamp Hour

			Auto
	HDMI Settings	HDMI Format
	HDMI Settings	HDMI Format	PC Signal

			Video Signal

Advanced	Baud Rate		2400/4800/9600/14400/19200/38400/57600/
Advanced	Baud Rate		115200
Setup
Setup	Test Pattern

	High Altitude Mode		On/Off

	Password	Password	On/Off

		Change Password	(inputs current password)
		Change Password	(inputs current password)

	Key Lock

	Reset All Settings

	ISF		(inputs current password)

Source

Picture Mode

Information Resolution

Equivalent Lamp Hour

Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

The default values listed in this manual, especially on pages 39-41, are for reference only. They may vary between the projectors due to the continuous improvement to the products.

38 Using the projector

Image 38

Contents Welcome W6000/W6500 Digital Projector Home Cinema SeriesTable of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Shipping contents OverviewCeiling mounting the projector Remote control batteriesRemote control operation Projector features Rear view Projector exterior viewFront and upper side view Under viewControl panel Test Remote controlPicture window control keys PIP, Size InfoCeiling Front Choosing a locationFloor Front Floor RearObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenLens Installation for a 43 ratio screenHighest Height HShifting the projection lens To use the lens shift leverReference Picture quality Connecting Hdmi devicesPreparations ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on PreparationsAdjust the projected picture to the size that Fine-tuning the image size and clarityUsing the OSD menu You need using the zoom ring RingUse / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password To leave the OSD menu, press MenuDisabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Two parallel sidesFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To fine-tune the picture modePress to highlight Load Settings From Setting the User 1/User 2/User 3 modeResetting the picture mode To reset the picture mode to the preset factory valuesFine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To set a preferred color temperatureColor Management Setting Film ModeTo adjust and store the settings About the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio Aspect ratio Aspect ratio image Using Panamorph lenses optionalImage Using the entire resolution 169 displayTo activate High Altitude Mode Operating in a high altitude environmentHighlight PIP and press / to select On To display the PIP window Using the remote controlDisplaying more than one image source simultaneously PIP function is effective at below source combinationsTurning the projector off Personalizing the projector menu displayLocking control keys To lock the keysMain menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Information Resolution System SetupSetup Function Description Picture -- Basic menuPicture -- Advanced menu System Setup menu Display menuLamp Power Normal Menu SettingsAdvanced Setup menu Reset Lamp TimerInformation menu Care of the projector Cleaning the lensCleaning the projector case Storing the projectorLamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Remove the lamp cover Resetting the lamp timer Power IndicatorsPower Temp Lamp Status & Description Lamp Status & DescriptionTroubleshooting Problem Cause RemedyElectrical SpecificationsOptical TerminalsMm x 317 mm x 145 mm W x D x H DimensionsCeiling mount installation Supported timing for PC input Timing chartFormat Resolution Refresh rate Frequency KHz MHzSupported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsDisclaimer WarrantyCopyright MIC statement FCC statement for United States usersEEC statement for European users Weee directiveEnglish