BenQ W6500 user manual Care of the projector, Cleaning the lens, Cleaning the projector case

Page 43

Additional information

Care of the projector

Your projector needs little maintenance. The only thing you have to do on a regular basis is keep the lens clean. Never remove any parts of the projector except the lamp. Contact your dealer or local customer service center if the projector fails to operate as expected.

Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface. Before you attempt to clean the lens, turn the projector off, unplug the power cable, and leave it several minutes to cool completely.

1.Use a canister of compressed air to remove dust. (Available from building hardware or photographic suppliers.)

2.If there is stubborn dirt or smudge marks, use a proper photographic lens brush or moisten a clean soft lens cloth with lens cleaner to gently wipe the lens surface.

3.Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the projector surface and cabinet material.

Never touch the lens with your finger or rub the lens with abrasive materials. Even paper towels can damage the lens coating. Only ever use a proper photographic lens brush, cloth, and cleaning solution. Do not attempt to clean the lens while the projector is switched on or is still hot from previous use.

Cleaning the projector case

Before you attempt to clean the case, turn the projector off, unplug the power cable, and leave it several minutes to cool completely.

1.To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth.

2.To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent. Then wipe the case.

Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.

Storing the projector

If you need to store the projector for an extended time, please:

1.Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to the Spec. page in this manual or consult your dealer about the range.

2.Retract the adjuster feet.

3.Remove the batteries from the remote control.

4.Pack the projector in its original packing or equivalent.

Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent.

English

Additional information

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents W6000/W6500 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Overview Shipping contentsRemote control operation Remote control batteriesCeiling mounting the projector Projector features Under view Projector exterior viewFront and upper side view Rear viewControl panel Info Remote controlPicture window control keys PIP, Size TestFloor Rear Choosing a locationFloor Front Ceiling FrontDetermine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeInstallation for a 169 ratio screen Projection dimensionsHeight H Installation for a 43 ratio screenHighest LensTo use the lens shift lever Shifting the projection lensComponent Connecting Hdmi devicesPreparations Reference Picture qualityConnecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerPreparations Turning the projector onYou need using the zoom ring Ring Fine-tuning the image size and clarityUsing the OSD menu Adjust the projected picture to the size thatSecuring the projector Using the menusUsing a security cable lock Use / to highlight the System Setup menuTo leave the OSD menu, press Menu Utilizing the password functionSetting a password If you forget the passwordWrite down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password functionTwo parallel sides Adjusting the projected imageAdjusting the projection angle Correcting picture distortionTo fine-tune the picture mode Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeTo reset the picture mode to the preset factory values Setting the User 1/User 2/User 3 modeResetting the picture mode Press to highlight Load Settings FromFine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsTo set a preferred color temperature Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant ColorTo adjust and store the settings Setting Film ModeColor Management Selecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio 169 display Using Panamorph lenses optionalImage Using the entire resolution Aspect ratio Aspect ratio imageOperating in a high altitude environment To activate High Altitude ModePIP function is effective at below source combinations To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Highlight PIP and press / to select OnTo lock the keys Personalizing the projector menu displayLocking control keys Turning the projector offOn-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Setup System SetupInformation Resolution Picture -- Advanced menu Picture -- Basic menuFunction Description Display menu System Setup menuReset Lamp Timer Menu SettingsAdvanced Setup menu Lamp Power NormalInformation menu Storing the projector Cleaning the lensCleaning the projector case Care of the projectorGetting to know the lamp hour Setting Lamp Power as EconomicSetting Auto Off Lamp informationReplacing the lamp Timing of replacing the lampStatus Message Remove the lamp cover Resetting the lamp timer Lamp Status & Description IndicatorsPower Temp Lamp Status & Description PowerProblem Cause Remedy TroubleshootingTerminals SpecificationsOptical ElectricalCeiling mount installation DimensionsMm x 317 mm x 145 mm W x D x H KHz MHz Timing chartFormat Resolution Refresh rate Frequency Supported timing for PC inputSupported timing for Video and S-Video inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Edtv and Hdtv via Component inputsCopyright WarrantyDisclaimer Weee directive FCC statement for United States usersEEC statement for European users MIC statementEnglish
Top Page Image Contents