BenQ W6500 user manual Do not cover the projector with any item

Page 4

English

5.Do not block the vents holes while the projector is on (even in standby mode):

-Do not cover the projector with any item;

-Do not place the projector on a blanket, bedding or any other soft surface.

6.In areas where the mains power supply voltage may fluctuate by ±10 volts, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS) as appropriate to your situation.

7.Do not step on the projector or place any objects upon it.

8.Do not place liquids near or on the projector. Liquids spilled into the projector will void your warranty. If the projector does become wet, disconnect it from the power point and call BenQ to have the projector repaired.

9.Do not look straight into the projector lens during operation. It may harm your sight.

10.Do not operate the projector lamp beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause a lamp to break on rare occasions.

11.The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

12.This projector is capable of displaying inverted images for ceiling mount installation. Use only BenQ's Ceiling Mount Kit for mounting.

4	Important safety instructions

Image 4

Contents Welcome W6000/W6500 Digital Projector Home Cinema SeriesTable of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control operation Remote control batteriesCeiling mounting the projector Projector features Projector exterior view Front and upper side viewRear view Under viewControl panel Remote control Picture window control keys PIP, SizeTest InfoChoosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsReference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on PreparationsFine-tuning the image size and clarity Using the OSD menuAdjust the projected picture to the size that You need using the zoom ring RingUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MenuEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Two parallel sidesUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To fine-tune the picture modeSetting the User 1/User 2/User 3 mode Resetting the picture modePress to highlight Load Settings From To reset the picture mode to the preset factory valuesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureTo adjust and store the settings Setting Film ModeColor Management Selecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayTo activate High Altitude Mode Operating in a high altitude environmentTo display the PIP window Using the remote control Displaying more than one image source simultaneouslyHighlight PIP and press / to select On PIP function is effective at below source combinationsPersonalizing the projector menu display Locking control keysTurning the projector off To lock the keysOn-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Setup System SetupInformation Resolution Picture -- Advanced menu Picture -- Basic menuFunction Description System Setup menu Display menuMenu Settings Advanced Setup menuLamp Power Normal Reset Lamp TimerInformation menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Power as Economic Setting Auto OffLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message Remove the lamp cover Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionPower Lamp Status & DescriptionTroubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsCeiling mount installation DimensionsMm x 317 mm x 145 mm W x D x H Timing chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsCopyright WarrantyDisclaimer FCC statement for United States users EEC statement for European usersMIC statement Weee directiveEnglish