BenQ W6500 Remote control batteries, Remote control operation, Ceiling mounting the projector

Page 7

Remote control batteries

1. To open the battery cover, turn the remote control over to view its back, push on the finger grip on the cover and slide it down in the direction of the arrow as illustrated. The cover will slide off.

2.Remove any existing batteries (if necessary)

and install two new AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive (+) goes to positive and negative (-) goes to negative.

3.Refit the cover by aligning it with the case and sliding it back up into position. Stop when it clicks into place.

Notes on handling batteries

Do not mix old batteries with new ones, or mix different types of batteries.

Avoid leaving the remote control and batteries in an excessive hot or humid environment like the kitchen, bathroom, sauna, sunroom, or in a closed car.

Dispose of used batteries according to the battery manufacturer’s instructions and local environment

regulations for your region.

If the remote control will not be used for an extended period of time, remove the batteries to avoid damage to the control from possible battery leakage.

Remote control operation

• Make sure that there is nothing positioned between

 

the remote control and the infrared (IR) sensors on

 

the projector that might obstruct the IR beam from

up to 8 m

the remote control reaching the projector.

 

The effective range of the remote control is up to 8 meters, and at an angle within 45 degrees of the IR beam. Always aim straight at the projector, however most screens will also reflect the IR beam to the projector.

Ceiling mounting the projector

We want you to have a pleasant experience using your BenQ projector, so we need to bring this safety matter to your attention to prevent damage to person and property.

If you intend to mount your projector on the ceiling, we strongly recommend that you use a proper fitting BenQ projector ceiling mount kit and that you ensure it is securely and safely installed.

If you use a non-BenQ brand projector ceiling mount kit, there is a safety risk that the projector may fall from the ceiling due to an improper attachment through the use of the wrong gauge or length screws.

You can purchase a BenQ projector ceiling mount kit from the place you purchased your BenQ projector. BenQ recommends that you also purchase a separate Kensington lock compatible security cable and attach it securely to both the Kensington lock slot on the projector and the base of the ceiling mount bracket. This will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose.

English

Overview 7

Image 7
Contents W6000/W6500 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Overview Shipping contentsRemote control operation Remote control batteriesCeiling mounting the projector Projector features Under view Projector exterior viewFront and upper side view Rear viewControl panel Info Remote controlPicture window control keys PIP, Size TestFloor Rear Choosing a locationFloor Front Ceiling FrontDetermine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeInstallation for a 169 ratio screen Projection dimensionsHeight H Installation for a 43 ratio screenHighest LensTo use the lens shift lever Shifting the projection lensComponent Connecting Hdmi devicesPreparations Reference Picture qualityConnecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerPreparations Turning the projector onYou need using the zoom ring Ring Fine-tuning the image size and clarityUsing the OSD menu Adjust the projected picture to the size thatSecuring the projector Using the menusUsing a security cable lock Use / to highlight the System Setup menuTo leave the OSD menu, press Menu Utilizing the password functionSetting a password If you forget the passwordWrite down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password functionTwo parallel sides Adjusting the projected imageAdjusting the projection angle Correcting picture distortionTo fine-tune the picture mode Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeTo reset the picture mode to the preset factory values Setting the User 1/User 2/User 3 modeResetting the picture mode Press to highlight Load Settings FromFine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsTo set a preferred color temperature Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant ColorTo adjust and store the settings Setting Film ModeColor Management Selecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio 169 display Using Panamorph lenses optionalImage Using the entire resolution Aspect ratio Aspect ratio imageOperating in a high altitude environment To activate High Altitude ModePIP function is effective at below source combinations To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Highlight PIP and press / to select OnTo lock the keys Personalizing the projector menu displayLocking control keys Turning the projector offOn-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Setup System SetupInformation Resolution Picture -- Advanced menu Picture -- Basic menuFunction Description Display menu System Setup menuReset Lamp Timer Menu SettingsAdvanced Setup menu Lamp Power NormalInformation menu Storing the projector Cleaning the lensCleaning the projector case Care of the projectorGetting to know the lamp hour Setting Lamp Power as EconomicSetting Auto Off Lamp informationReplacing the lamp Timing of replacing the lampStatus Message Remove the lamp cover Resetting the lamp timer Lamp Status & Description IndicatorsPower Temp Lamp Status & Description PowerProblem Cause Remedy TroubleshootingTerminals SpecificationsOptical ElectricalCeiling mount installation DimensionsMm x 317 mm x 145 mm W x D x H KHz MHz Timing chartFormat Resolution Refresh rate Frequency Supported timing for PC inputSupported timing for Video and S-Video inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Edtv and Hdtv via Component inputsCopyright WarrantyDisclaimer Weee directive FCC statement for United States usersEEC statement for European users MIC statementEnglish