BenQ W6500 user manual Resetting the lamp timer

Page 47

Resetting the lamp timer

Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.

English

1. After the start-up logo, press MENU and then press / until the Advanced Setup menu is highlighted.

2.Press to highlight Lamp Settings and press ENTER. The Lamp Settings page displays.

3.Highlight Reset Lamp Timer and press ENTER. A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press ENTER. The lamp time will be reset to "0".

Advanced Setup

Lamp Settings	ENTER
HDMI Settings
Baud Rate	115200
Test Pattern
High Altitude Mode	Off
Password
Key Lock
Reset All Settings
ISF
S-Video	EXIT	Back
Lamp Settings
Lamp Power	Normal
Reset Lamp Timer	ENTER
Equivalent Lamp Hour
	EXIT	Back

WARNING

Reset Lamp Timer?

Reset Cancel

Additional information

Image 47

Contents W6000/W6500 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Overview Shipping contentsCeiling mounting the projector Remote control batteriesRemote control operation Projector features Under view Projector exterior viewFront and upper side view Rear viewControl panel Info Remote controlPicture window control keys PIP, Size TestFloor Rear Choosing a locationFloor Front Ceiling FrontDetermine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeInstallation for a 169 ratio screen Projection dimensionsHeight H Installation for a 43 ratio screenHighest LensTo use the lens shift lever Shifting the projection lensComponent Connecting Hdmi devicesPreparations Reference Picture qualityConnecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerPreparations Turning the projector onYou need using the zoom ring Ring Fine-tuning the image size and clarityUsing the OSD menu Adjust the projected picture to the size thatSecuring the projector Using the menusUsing a security cable lock Use / to highlight the System Setup menuTo leave the OSD menu, press Menu Utilizing the password functionSetting a password If you forget the passwordWrite down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password functionTwo parallel sides Adjusting the projected imageAdjusting the projection angle Correcting picture distortionTo fine-tune the picture mode Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeTo reset the picture mode to the preset factory values Setting the User 1/User 2/User 3 modeResetting the picture mode Press to highlight Load Settings FromFine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsTo set a preferred color temperature Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film ModeTo adjust and store the settings About the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio 169 display Using Panamorph lenses optionalImage Using the entire resolution Aspect ratio Aspect ratio imageOperating in a high altitude environment To activate High Altitude ModePIP function is effective at below source combinations To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Highlight PIP and press / to select OnTo lock the keys Personalizing the projector menu displayLocking control keys Turning the projector offMain menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Information Resolution System SetupSetup Function Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menuReset Lamp Timer Menu SettingsAdvanced Setup menu Lamp Power NormalInformation menu Storing the projector Cleaning the lensCleaning the projector case Care of the projectorGetting to know the lamp hour Setting Lamp Power as EconomicSetting Auto Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Remove the lamp cover Resetting the lamp timer Lamp Status & Description IndicatorsPower Temp Lamp Status & Description PowerProblem Cause Remedy TroubleshootingTerminals SpecificationsOptical ElectricalMm x 317 mm x 145 mm W x D x H DimensionsCeiling mount installation KHz MHz Timing chartFormat Resolution Refresh rate Frequency Supported timing for PC inputSupported timing for Video and S-Video inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Edtv and Hdtv via Component inputsDisclaimer WarrantyCopyright Weee directive FCC statement for United States usersEEC statement for European users MIC statementEnglish