BenQ W6500 user manual Warranty, Copyright, Disclaimer

Page 54

English

Warranty and Copyright information

Warranty

BenQ warrants this product against any defects in material and workmanship, under normal usage and storage.

Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ’s only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.

Important: The above warranty shall be void if the customer fails to operate the product in accordance with BenQ’s written instructions, especially the ambient humidity must be in-between 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 3000 meters, and avoiding to operate the projector in a dusty environment. This warranty gives you specific legal rights, and you may have other rights which vary from country to country.

For other information, please visit www.BenQ.com.

Copyright

Copyright © 2009 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.

All trademarks and registered trademarks are the property of their respective owners.

Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of BenQ Corporation to notify any person of such revision or changes.

54 Warranty and Copyright information

Image 54

Contents Welcome W6000/W6500 Digital Projector Home Cinema SeriesTable of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewRemote control batteries Remote control operationCeiling mounting the projector Projector features Rear view Projector exterior viewFront and upper side view Under viewControl panel Test Remote controlPicture window control keys PIP, Size InfoCeiling Front Choosing a locationFloor Front Floor RearObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenLens Installation for a 43 ratio screenHighest Height HShifting the projection lens To use the lens shift leverReference Picture quality Connecting Hdmi devicesPreparations ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on PreparationsAdjust the projected picture to the size that Fine-tuning the image size and clarityUsing the OSD menu You need using the zoom ring RingUse / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password To leave the OSD menu, press MenuDisabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Two parallel sidesFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To fine-tune the picture modePress to highlight Load Settings From Setting the User 1/User 2/User 3 modeResetting the picture mode To reset the picture mode to the preset factory valuesFine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To set a preferred color temperatureSetting Film Mode To adjust and store the settingsColor Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Aspect ratio Aspect ratio image Using Panamorph lenses optionalImage Using the entire resolution 169 displayTo activate High Altitude Mode Operating in a high altitude environmentHighlight PIP and press / to select On To display the PIP window Using the remote controlDisplaying more than one image source simultaneously PIP function is effective at below source combinationsTurning the projector off Personalizing the projector menu displayLocking control keys To lock the keysOn-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup SetupInformation Resolution Picture -- Basic menu Picture -- Advanced menuFunction Description System Setup menu Display menuLamp Power Normal Menu SettingsAdvanced Setup menu Reset Lamp TimerInformation menu Care of the projector Cleaning the lensCleaning the projector case Storing the projectorLamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message Remove the lamp cover Resetting the lamp timer Power IndicatorsPower Temp Lamp Status & Description Lamp Status & DescriptionTroubleshooting Problem Cause RemedyElectrical SpecificationsOptical TerminalsDimensions Ceiling mount installationMm x 317 mm x 145 mm W x D x H Supported timing for PC input Timing chartFormat Resolution Refresh rate Frequency KHz MHzSupported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsWarranty CopyrightDisclaimer MIC statement FCC statement for United States usersEEC statement for European users Weee directiveEnglish