BenQ W6500 Utilizing the password function, Setting a password, If you forget the password

Page 23

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. Once the password is set and this function is selected, the projector is password-protected. Users who do not know the correct password can not use the projector.

You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print out this manual (if necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall.

Setting a password

Once a password has been set and activated, the projector cannot be used unless the correct password is entered every time the projector is started.

English

1.Press MENU on the projector or remote control and then press / until the Advanced Setup menu is highlighted.

2.Press to highlight Password and press ENTER. The Password page displays.

3.Highlight Password and press / to select On. The Input Password page displays.

4.As the picture indicates, the four arrow keys ( , , , ) respectively represent 4 digits (1, 2, 3, 4). According to the password you desire to set, press the arrow keys on the remote control or projector to enter six digits for the password.

If the function is used for the first time, enter the default password (1, 1, 1, 1, 1, 1) of the projector by pressing the arrow key six times. Once the password is set, the OSD menu returns to the Password page.

IMPORTANT: The digits being input will display as asterisks on- screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Advanced Setup

Lamp Settings

HDMI Settings

 

 

Baud Rate

115200

 

Test Pattern

 

 

High Altitude Mode

Off

 

Password

ENTER

 

Key Lock

 

 

Reset All Settings

 

 

ISF

 

 

S-Video

EXIT

Back

Password

 

 

Password

On

 

Change Password

 

 

 

EXIT

Back

Input Password

EXIT Clear

5. To leave the OSD menu, press MENU.

If you forget the password

If the password function is activated, you will be asked to enter the six- digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right displays lasting for three seconds, and the Input Password page follows. You can retry by entering another six-digit password, or if you did not record the password in this manual, and you absolutely do not remember it, you can use the password recall procedure. See "Entering the password recall procedure" on page 24 for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

Password Error

Please try again.

Using the projector

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents W6000/W6500 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Overview Shipping contentsCeiling mounting the projector Remote control batteriesRemote control operation Projector features Under view Projector exterior viewFront and upper side view Rear viewControl panel Info Remote controlPicture window control keys PIP, Size TestFloor Rear Choosing a locationFloor Front Ceiling FrontDetermine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeInstallation for a 169 ratio screen Projection dimensionsHeight H Installation for a 43 ratio screenHighest LensTo use the lens shift lever Shifting the projection lensComponent Connecting Hdmi devicesPreparations Reference Picture qualityConnecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerPreparations Turning the projector onYou need using the zoom ring Ring Fine-tuning the image size and clarityUsing the OSD menu Adjust the projected picture to the size thatSecuring the projector Using the menusUsing a security cable lock Use / to highlight the System Setup menuTo leave the OSD menu, press Menu Utilizing the password functionSetting a password If you forget the passwordWrite down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password functionTwo parallel sides Adjusting the projected imageAdjusting the projection angle Correcting picture distortionTo fine-tune the picture mode Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeTo reset the picture mode to the preset factory values Setting the User 1/User 2/User 3 modeResetting the picture mode Press to highlight Load Settings FromFine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsTo set a preferred color temperature Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film ModeTo adjust and store the settings About the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio 169 display Using Panamorph lenses optionalImage Using the entire resolution Aspect ratio Aspect ratio imageOperating in a high altitude environment To activate High Altitude ModePIP function is effective at below source combinations To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Highlight PIP and press / to select OnTo lock the keys Personalizing the projector menu displayLocking control keys Turning the projector offMain menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Information Resolution System SetupSetup Function Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menuReset Lamp Timer Menu SettingsAdvanced Setup menu Lamp Power NormalInformation menu Storing the projector Cleaning the lensCleaning the projector case Care of the projectorGetting to know the lamp hour Setting Lamp Power as EconomicSetting Auto Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Remove the lamp cover Resetting the lamp timer Lamp Status & Description IndicatorsPower Temp Lamp Status & Description PowerProblem Cause Remedy TroubleshootingTerminals SpecificationsOptical ElectricalMm x 317 mm x 145 mm W x D x H DimensionsCeiling mount installation KHz MHz Timing chartFormat Resolution Refresh rate Frequency Supported timing for PC inputSupported timing for Video and S-Video inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Edtv and Hdtv via Component inputsDisclaimer WarrantyCopyright Weee directive FCC statement for United States usersEEC statement for European users MIC statementEnglish
Top Page Image Contents