BenQ MX710, MX711 Remote control effective range, Replacing the remote control batteries, Ppr 15º

Page 13

Remote control effective range

Infra-Red (IR) remote control sensors are located on the front and the top of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensors to function correctly. The distance between the remote control and the sensors should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensors on the projector that might obstruct the infra-red beam.

• Operating the projector from the front • Operating the projector from the top

A

 

 

 

 

ppr

 

 

 

 

o

 

Ap

 

 

x.+1

5

pr

 

 

º

 

o

 

 

 

 

x.+

 

 

 

 

15º

Replacing the remote control batteries

1.To open the battery cover, turn the remote control over to view its back, push on the finger grip on the cover and slide it up in the direction of the arrow as illustrated. The cover will slide off.

2.Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive (+) goes to positive and negative (-) goes to negative.

3.Refit the cover by aligning it with the base and sliding it back down into position. Stop when it clicks into place.

Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car.

Replace only with the same or equivalent type recommended by the battery manufacturer.

Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region.

Never throw the batteries into a fire. There may be danger of an explosion.

If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible

battery leakage.

Introduction 13

Image 13
Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewLamp cover External control panel Projector Controls and functionsTest Remote controlKeystone/Arrow buttons / Up Down Mute Operating the Laser pointerMIC/VOL + Numeric buttonsReplacing the remote control batteries Remote control effective rangePpr 15º Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal VerticalConnection Connecting audio Connecting video source devicesTerminal name Terminal appearance BestAbout the microphone input Playing sound through the projectorPage Starting up the projector OperationDetails OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityFollowing example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Correcting keystone Disabling the password functionTo correct keystoning at the bottom of the image Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAdjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management To cancel the timer, perform the following steps Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-RightRemote paging operations Utilizing FAQ functionFreezing the image Hiding the imageLocking control keys To activate the High Altitude ModeOperating in a high altitude environment Creating your own startup screenAdjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring ToneCable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options BasicAdvanced Lamp Mode Normal/Economic Lamp SettingsMessage Equivalent Lamp HourAdvanced Network Description of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function DescriptionTimer System Setup Basic menu Function Description Quick AutoSettings SearchPanel Key Settings Security DescriptionBackground LockReset All System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampLamp cover loosens Remove the lamp cover from the projector Replacing the lampUse the handle to slowly pull the lamp out Projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmSupported timing for PC input Timing chart1360 x Supported timing for Hdmi Hdcp inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users Weee directive
Related manuals
Manual 2 pages 34.84 Kb