BenQ MX711, MX710 user manual Use the handle to slowly pull the lamp out Projector

Page 64

7.Use the handle to slowly pull the lamp out of

the projector.

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

•Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

8. As shown in the figure, lower the new lamp.

9.	Tighten the screw that secures the lamp.
10.	Ensure the handle is fully laid flat and locked	2
	in place.

• Loose screw may cause a bad connection, which could result in malfunction.

1

• Do not over tighten the screw.

11.Replace the new protection film that comes with the new lamp.

12. Replace the lamp cover on the projector.

13.Tighten the screw that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

64 Maintenance

Image 64

Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewLamp cover External control panel Controls and functions ProjectorTest Remote controlKeystone/Arrow buttons / Up Down Operating the Laser pointer MuteMIC/VOL + Numeric buttonsReplacing the remote control batteries Remote control effective rangePpr 15º Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal VerticalConnection Connecting video source devices Connecting audioTerminal name Terminal appearance BestPlaying sound through the projector About the microphone inputPage Operation Starting up the projectorDetails OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityFollowing example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Correcting keystone Disabling the password functionTo correct keystoning at the bottom of the image Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Setting the presentation timer To cancel the timer, perform the following stepsSelection Description Top-Left Bottom-Left Top-Right Bottom-RightUtilizing FAQ function Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Locking control keysOperating in a high altitude environment Creating your own startup screenAdjusting the sound Adjusting the sound levelAdjusting the microphone volume Turning off the Power On/Off Ring ToneControlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu operation Menu systemMain menu Sub-menu Options BasicLamp Mode Normal/Economic Lamp Settings AdvancedMessage Equivalent Lamp HourAdvanced Network Description of each menu Picture Mode TemperatureManagement Save Settings Display menu Picture menu Function DescriptionSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchSettings Security Description Panel KeyBackground LockSystem Setup Advanced menu Function Description Reset AllBaud Rate Test PatternFeatures Service CurrentSystem StatusMaintenance Care of the projector Setting Lamp Mode as Economic Setting Auto Power Off Lamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Lamp cover loosens Remove the lamp cover from the projectorUse the handle to slowly pull the lamp out Projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25Ceiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input 1360 xSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Warranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statement for United States usersEEC statement for European users Weee directive

Related manuals

Manual 2 pages 34.84 Kb