BenQ MX710, MX711 user manual Features Service, Current, System, Status

Page 59

6. INFORMATION menu

Function

Description

FAQ-Image

 

and

 

Installation

Displays possible solutions to problems you may encounter.

 

FAQ-

 

Features and

 

Service

 

 

 

 

Source

 

Shows the current signal source.

 

Picture Mode

 

Shows the selected mode in the PICTURE menu.

Current

Resolution

Shows the native resolution of the input signal.

System

Color System

Status

Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.

 

 

Equivalent Lamp Hour

 

Displays the number of hours the lamp has been used.

 

Firmware Version

 

Shows the firmware version of your projector.

 

 

Operation 59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedIntroduction Projector featuresIntroduction Shipping contents Lamp cover External control panel Projector exterior viewRear/lower side Projector Controls and functionsKeystone/Arrow buttons / Up Down Remote controlTest Numeric buttons Operating the Laser pointerMute MIC/VOL +Ppr 15º Remote control effective rangeReplacing the remote control batteries Front Ceiling Positioning your projectorChoosing a location Front TableVertical Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm DiagonalConnection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceAbout the microphone input Playing sound through the projectorPage Operation OperationStarting up the projector DetailsFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageUse / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordChanging the password If you forget the passwordEntering the password recall procedure To correct keystoning at the bottom of the image Disabling the password functionCorrecting keystone Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageCreating your own startup screen To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Basic Menu operationMenu system Main menu Sub-menu OptionsEquivalent Lamp Hour Lamp Mode Normal/Economic Lamp SettingsAdvanced MessageAdvanced Network Description of each menu Display menu Picture menu Function Description Picture ModeTemperature Management Save Settings Search System Setup Basic menu Function Description Quick Auto Timer SettingsLock Settings Security DescriptionPanel Key BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampLamp cover loosens Remove the lamp cover from the projector Replacing the lampUse the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsUnit mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Ceiling Mount screw M4 x 8 Max L = 8 mmSupported timing for PC input Timing chart1360 x Supported timing for Hdmi Hdcp inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users
Related manuals
Manual 2 pages 34.84 Kb
Top Page Image Contents