BenQ MX711, MX710 user manual Switching input signal, Changing Color Space

Page 26

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals.

Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.

To select the source:

•Using the remote control or projector

Press one of the Source buttons on the remote control, or press SOURCE on the projector repeatedly until your desired signal is selected.

•Using the OSD menu

1.Press SOURCE on the projector or remote control. A source selection bar displays.

2.Press / until your desired signal is selected and press MODE/ENTER.

Once detected, the selected source information will display at the corner of the screen for seconds. If there is multiple equipment connected to the projector, repeat steps 1-2 to search for another signal.

•The brightness level of the projected image will change accordingly when you switch between different input signals. Data (graphic) "PC" presentations using mostly static images are generally brighter than "Video" using mostly moving images (movies).

Computer1/YPbPr1

Computer2/YPbPr2

HDMI

Video

S-Video

Network Display

USB Display

USB Reader

•The native display resolution of this projector is in a 4:3 aspect ratio. For best display picture results, you should select and use an input signal which outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the “aspect ratio” setting, which may cause some image distortion or loss of picture clarity. See "Selecting the aspect ratio" on page 27 for details.

•Firewall in the PC must be switched off to allow Q Presenter and USB Display to work.

Changing Color Space

In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to YUV.

To do this:

1.Press MENU/EXIT and then press / until the SOURCE menu is highlighted.

2.Press to highlight Color Space Conversion and press / to select a suitable color space.

This function is only available when the HDMI-input port is in use.

26 Operation

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Lamp cover External control panel Projector exterior viewRear/lower side Controls and functions ProjectorKeystone/Arrow buttons / Up Down Remote controlTest MIC/VOL + Operating the Laser pointerMute Numeric buttonsPpr 15º Remote control effective rangeReplacing the remote control batteries Front Table Positioning your projectorChoosing a location Front CeilingScreen size Distance from screen mm Diagonal Projection dimensionsObtaining a preferred projected image size VerticalConnection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestPlaying sound through the projector About the microphone inputPage Details OperationStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure To correct keystoning at the bottom of the image Disabling the password functionCorrecting keystone Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Selection Description Setting the presentation timerTo cancel the timer, perform the following steps Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Utilizing FAQ functionRemote paging operations Hiding the imageOperating in a high altitude environment To activate the High Altitude ModeLocking control keys Creating your own startup screenAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system BasicMessage Lamp Mode Normal/Economic Lamp SettingsAdvanced Equivalent Lamp HourAdvanced Network Description of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function DescriptionSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground Settings Security DescriptionPanel Key LockBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternSystem Features ServiceCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Lamp cover loosens Remove the lamp cover from the projectorUse the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsCeiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input 1360 xTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users Weee directive
Related manuals
Manual 2 pages 34.84 Kb
Top Page Image Contents