BenQ MX711, MX710 user manual Description of each menu

Page 54

Description of each menu

1. DISPLAY menu

Function

Description

Wall Color

Corrects the projected picture’s color when the projection surface is not

white. See "Using Wall Color" on page 29 for details.

 

 

 

Aspect Ratio

There are several options to set the image's aspect ratio depending on

your input signal source. See "Selecting the aspect ratio" on page 27 for

 

details.

 

 

Auto

Automatically corrects any keystoning of the image. See "Correcting

Keystone

keystone" on page 25 for details.

 

 

Keystone

Corrects any keystoning of the image. See "Correcting keystone" on

page 25 for details.

 

 

 

 

Displays the position adjustment page. To move the projected image,

 

use the directional arrow keys. The values shown on the lower position

Position

of the page change with every key press you made until they reach their

maximum or minimum.

 

This function is only available when a PC signal (analog RGB) is

 

selected.

 

Adjusts the clock phase to reduce image

 

distortion.

Phase

 

 

This function is only available when a PC

 

signal (analog RGB) is selected.

H. Size

Adjusts the horizontal width of the image.

This function is only available when a PC signal (analog RGB) is

 

selected.

Digital Zoom

Magnifies or reduces the projected image. See "Magnifying and

searching for details" on page 27 for details.

 

 

 

 

This projector features a 3D function which enables you to enjoy the

 

3D movies, videos, and sporting events in a more realistic way by

 

presenting the depth of the images. You need to wear a pair of 3D

 

glasses to view the 3D images.

 

• For a PC type signal:

 

When the vertical frequency is 60Hz or 120Hz, and the content being

 

projected is made with 3D technology, selecting On will present the 3D

3D Sync

images.

• For a video type signal:

 

 

When the content being projected is made with 3D technology,

 

selecting On will present the 3D images.

 

When the 3D Sync function is On:

 

• The brightness level of the projected image will decrease.

 

• The Picture Mode cannot be adjusted.

 

• The Keystone can only be adjusted within limited degrees.

3D Sync

When you discover the inversion of the image depth, enable this

Invert

function to correct the problem.

 

 

54 Operation

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Rear/lower sideLamp cover External control panel Controls and functions ProjectorRemote control TestKeystone/Arrow buttons / Up Down MIC/VOL + Operating the Laser pointerMute Numeric buttonsRemote control effective range Replacing the remote control batteriesPpr 15º Front Table Positioning your projectorChoosing a location Front CeilingScreen size Distance from screen mm Diagonal Projection dimensionsObtaining a preferred projected image size VerticalConnection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestPlaying sound through the projector About the microphone inputPage Details OperationStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Correcting keystoneTo correct keystoning at the bottom of the image Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Selection Description Setting the presentation timerTo cancel the timer, perform the following steps Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Utilizing FAQ functionRemote paging operations Hiding the imageOperating in a high altitude environment To activate the High Altitude ModeLocking control keys Creating your own startup screenAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Main menu Sub-menu Options Menu operationMenu system BasicMessage Lamp Mode Normal/Economic Lamp SettingsAdvanced Equivalent Lamp HourAdvanced Network Description of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function DescriptionSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground Settings Security DescriptionPanel Key LockBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternSystem Features ServiceCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Lamp cover loosens Remove the lamp cover from the projectorUse the handle to slowly pull the lamp out Projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsCeiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input 1360 xSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users Weee directive
Related manuals
Manual 2 pages 34.84 Kb
Top Page Image Contents