BenQ MX711, MX710 user manual Specifications, Projector specifications

Page 68

Specifications

Projector specifications

All specifications are subject to change without notice.

Optical

Resolution

1024 x 768 XGA

Display system 1-CHIP DMD

Lens F/Number

F= 2.59-2.87 Lamp (MX710)

210 W lamp

(MX711)

230 W lamp

Electrical

Power supply

AC100–240V, 3.8 A, 50-60 Hz (Automatic) Power consumption

(MX710)

336 W (Max); < 1 W (Standby) (MX711)

362 W (Max); < 1 W (Standby)

Mechanical

Weight

5.84 lbs (2.65 Kg)

Output terminals

RGB output

D-Sub 15-pin (female) x 1 Speaker

(Stereo) 5 watt x 2 Audio signal output

PC audio jack x 1

Control

RS-232 serial control 9 pin x 1

Lan control RJ45 x 1

IR receiver x 2

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 2

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3 (through RGB input)

Digital - HDMI V1.3 x 1

Audio signal input Audio in

PC audio jack x 1

RCA audio jack (L/R) x 2 Microphone x 1

USB ports (Type-A x 1; Mini-B x 1)

Environmental Requirements

Operating temperature 0°C–40°C at sea level

Operating relative humidity 10%–90% (without condensation)

Operating altitude 0–1499 m at 0°C–35°C 1500–3000 m at 0°C–30°C (with High Altitude Mode on)

68 Specifications

Image 68

Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Lamp cover External control panel Projector exterior viewRear/lower side Controls and functions ProjectorKeystone/Arrow buttons / Up Down Remote controlTest Operating the Laser pointer MuteMIC/VOL + Numeric buttonsPpr 15º Remote control effective rangeReplacing the remote control batteries Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal VerticalConnection Connecting video source devices Connecting audioTerminal name Terminal appearance BestPlaying sound through the projector About the microphone inputPage Operation Starting up the projectorDetails OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure To correct keystoning at the bottom of the image Disabling the password functionCorrecting keystone Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Setting the presentation timer To cancel the timer, perform the following stepsSelection Description Top-Left Bottom-Left Top-Right Bottom-RightUtilizing FAQ function Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Locking control keysOperating in a high altitude environment Creating your own startup screenAdjusting the sound Adjusting the sound levelAdjusting the microphone volume Turning off the Power On/Off Ring ToneControlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Menu operation Menu systemMain menu Sub-menu Options BasicLamp Mode Normal/Economic Lamp Settings AdvancedMessage Equivalent Lamp HourAdvanced Network Description of each menu Picture Mode TemperatureManagement Save Settings Display menu Picture menu Function DescriptionSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchSettings Security Description Panel KeyBackground LockSystem Setup Advanced menu Function Description Reset AllBaud Rate Test PatternFeatures Service CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Lamp cover loosens Remove the lamp cover from the projectorUse the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25Ceiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input 1360 xTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statement for United States usersEEC statement for European users Weee directive

Related manuals

Manual 2 pages 34.84 Kb