BenQ MX711, MX710 user manual Operation

Page 48

•The Q Presenter only accepts up to 8 characters consisting of English capitalized letters and digits 0-9 for the name, full 6 digits consisting of 1 to 4 for the password.

•To change the Q Presenter interface language, click the down arrow to reveal a drop-down list and select a desired language. Click Apply.

•To allow notification messages to appear, click Yes. Click Apply.

•To display your computer screen on multiple projectors, click Activate 1:N Display. Click Apply. It can display up to 8 projectors at the same time.

4.The Advanced Settings page allows you to configure Q Presenter.

•To display still pictures, click the down arrow to reveal a drop-down list and select Graphic. Click Apply. To display video clips, click the down arrow to reveal a drop-down list and select Video. Click Apply.

Graphic mode: worse image quality but faster transmission speed.

Video mode: better image quality but slower transmission speed.

However, the actual transmission speed was determined by the network traffic at that time.

•To adjust the capture rate, move the slide bar. The network bandwidth may also affect the performance.

•To launch Q Presenter when your computer operating system is started, click Yes for Boot and launch. Click Apply.

•To link to the Projector Network Display System web page, click Link.

5.Disconnect

To disconnect from the projector(s), click the Disconnect icon.

• Be sure to turn off other virtual network control programs before using Q Presenter.

•Firewall in the PC must be switched off to allow Q Presenter and USB Display to work.

•Wireless keyboard mouse combo is not supported by Pixelworks currently.

48 Operation

Image 48

Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Rear/lower sideLamp cover External control panel Controls and functions ProjectorRemote control TestKeystone/Arrow buttons / Up Down Operating the Laser pointer MuteMIC/VOL + Numeric buttonsRemote control effective range Replacing the remote control batteriesPpr 15º Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal VerticalConnection Connecting video source devices Connecting audioTerminal name Terminal appearance BestPlaying sound through the projector About the microphone inputPage Operation Starting up the projectorDetails OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Correcting keystoneTo correct keystoning at the bottom of the image Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Setting the presentation timer To cancel the timer, perform the following stepsSelection Description Top-Left Bottom-Left Top-Right Bottom-RightUtilizing FAQ function Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Locking control keysOperating in a high altitude environment Creating your own startup screenAdjusting the sound Adjusting the sound levelAdjusting the microphone volume Turning off the Power On/Off Ring ToneControlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu operation Menu systemMain menu Sub-menu Options BasicLamp Mode Normal/Economic Lamp Settings AdvancedMessage Equivalent Lamp HourAdvanced Network Description of each menu Picture Mode TemperatureManagement Save Settings Display menu Picture menu Function DescriptionSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchSettings Security Description Panel KeyBackground LockSystem Setup Advanced menu Function Description Reset AllBaud Rate Test PatternFeatures Service CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Lamp cover loosens Remove the lamp cover from the projectorUse the handle to slowly pull the lamp out Projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25Ceiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input 1360 xSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Warranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statement for United States usersEEC statement for European users Weee directive

Related manuals

Manual 2 pages 34.84 Kb