BenQ MX710, MX711 Replacing the lamp, Lamp cover loosens Remove the lamp cover from the projector

Page 63

Replacing the lamp

•To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.

•To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

•To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.

•To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.

•This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.

•To assure optimal performance from the projector, it is recommended that you purchase a qualified projector lamp for lamp replacement.

•If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by fractured lamp.

1.Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2.Loosen the screw that secures the lamp cover on the side of the projector until the

lamp cover loosens.

3.Remove the lamp cover from the projector.

• Do not turn the power on with the lamp cover removed.

• Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

4.Remove and dispose the protection film.

5.	Loosen the screw that secures the lamp.	1
6.	Lift the handle so that it stands up.

2

Maintenance 63

Image 63

Contents Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedProjector features IntroductionIntroduction Shipping contents Projector exterior view Rear/lower sideLamp cover External control panel Projector Controls and functionsRemote control TestKeystone/Arrow buttons / Up Down Numeric buttons Operating the Laser pointerMute MIC/VOL +Remote control effective range Replacing the remote control batteriesPpr 15º Front Ceiling Positioning your projectorChoosing a location Front TableVertical Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm DiagonalConnection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceAbout the microphone input Playing sound through the projectorPage Operation OperationStarting up the projector DetailsFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Correcting keystoneTo correct keystoning at the bottom of the image Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageCreating your own startup screen To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Basic Menu operationMenu system Main menu Sub-menu OptionsEquivalent Lamp Hour Lamp Mode Normal/Economic Lamp SettingsAdvanced MessageAdvanced Network Description of each menu Display menu Picture menu Function Description Picture ModeTemperature Management Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsLock Settings Security DescriptionPanel Key BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus Features ServiceCurrent System Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampLamp cover loosens Remove the lamp cover from the projector Replacing the lampUse the handle to slowly pull the lamp out Projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsUnit mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Ceiling Mount screw M4 x 8 Max L = 8 mmSupported timing for PC input Timing chart1360 x Supported timing for Hdmi Hdcp inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users

Related manuals

Manual 2 pages 34.84 Kb