BenQ MX711 System Setup Advanced menu Function Description, Baud Rate, Test Pattern, Closed

Page 58

5. SYSTEM SETUP: Advanced menu

Function

Description

 

Selects a baud rate that is identical with your computer’s so that you can

Baud Rate

connect the projector using a suitable RS-232 cable and update or

download the projector’s firmware. This function is intended for

 

 

qualified service personnel.

 

 

Test Pattern

Selecting On enables the function and the projector displays the grid test

pattern. It helps you adjust the image size and focus and check that the

 

projected image is free from distortion.

 

 

 

Closed Caption Enable

 

Activates the function by selecting On when the selected input signal

 

carries closed captions.

 

• Captions: An on-screen display of the dialogue, narration, and

Closed

sound effects of TV programs and videos that are closed captioned

(usually marked as "CC" in TV listings).

Caption

Set your screen aspect ratio to 4:3. This function is not available

 

when the aspect ratio is “16:9” or “Real”.

 

Caption Version

 

Selects a preferred closed captioning mode. To view captions, select

 

CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language

 

in your area).

 

 

 

Network

 

Selecting On enables the function. The projector is able to provide the

 

network function when it is in standby mode.

 

Microphone

 

Selecting On enables the function. The projector can output the

 

microphone signal when it is in standby mode and all the necessary

Standby

equipment is correctly connected. See "Playing sound through the

projector" on page 18 for details.

Settings

Monitor Out

 

 

Selecting On enables the function. The projector can output a VGA

 

signal when it is in standby mode and the COMPUTER 1 jack is

 

correctly connected to devices. See "Connection" on page 16 for how to

 

make the connection.

 

Enabling this function slightly increases the standby power

 

consumption.

 

Wired LAN

Network

Wireless LAN

Remote Desktop

Settings

See "Controlling the projector through a LAN environment" on page 36

 

 

for details.

 

 

 

Returns all settings to the factory preset values.

Reset All

The following settings will still remain: Phase, H. Size, User 1, User

Settings

2, Language, Projector Position, High Altitude Mode, Security

 

Settings, Remote Receiver, DHCP, SSID, Remote Desktop and

 

Baud Rate.

58 Operation

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewLamp cover External control panel Controls and functions ProjectorTest Remote controlKeystone/Arrow buttons / Up Down MIC/VOL + Operating the Laser pointerMute Numeric buttonsReplacing the remote control batteries Remote control effective rangePpr 15º Front Table Positioning your projectorChoosing a location Front CeilingScreen size Distance from screen mm Diagonal Projection dimensionsObtaining a preferred projected image size VerticalConnection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestPlaying sound through the projector About the microphone inputPage Details OperationStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityFollowing example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Correcting keystone Disabling the password functionTo correct keystoning at the bottom of the image Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Selection Description Setting the presentation timerTo cancel the timer, perform the following steps Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Utilizing FAQ functionRemote paging operations Hiding the imageOperating in a high altitude environment To activate the High Altitude ModeLocking control keys Creating your own startup screenAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Main menu Sub-menu Options Menu operationMenu system BasicMessage Lamp Mode Normal/Economic Lamp SettingsAdvanced Equivalent Lamp HourAdvanced Network Description of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function DescriptionSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground Settings Security DescriptionPanel Key LockBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternSystem Features ServiceCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Lamp cover loosens Remove the lamp cover from the projectorUse the handle to slowly pull the lamp out Projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsCeiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input 1360 xSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users Weee directive
Related manuals
Manual 2 pages 34.84 Kb
Top Page Image Contents