BenQ MX710 Display menu Picture menu Function Description, Teaching, Template, Picture Mode, Tint

Page 55

1. DISPLAY menu

2. PICTURE menu

Function

Description

 

 

Provides several preset patterns for various teaching purposes.

Teaching

Choose Blackboard or Whiteboard first by pressing /

and press

/ to choose the pattern you need. Once you are done, go back to

Template

the PICTURE > Teaching Template > Blackboard or Whiteboard

 

(depending on which item you previously selected) menu and select

 

Off.

 

 

 

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 29 for details.

 

 

 

Reference

Selects a picture mode that best suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 29 for

 

details.

 

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on page

30 for details.

 

 

 

 

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 30 for details.

 

 

 

 

 

 

Adjusts the color saturation level -- the amount of each color in a video

Color

image. See "Adjusting Color" on page 30 for details.

 

This function is only available when a Video, S-Video or

 

 

Component Video signal is selected.

 

 

Adjusts the red and green color tones of the image. See "Adjusting Tint"

Tint

on page 30 for details.

 

This function is only available when a Video or S-Video signal is

 

 

selected and the system format is NTSC.

 

 

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness

Sharpness" on page 30 for details.

 

This function is only available when a Video, S-Video or

 

 

Component Video signal is selected.

 

Brilliant Color

See "Adjusting Brilliant Color" on page 30 for details.

 

 

 

Color

There are four color temperature settings available. See "Selecting a

Temperature

color temperature" on page 30 for details.

 

 

 

 

3D Color

See "3D Color Management" on page 31 for details.

 

Management

 

 

 

 

 

 

Save Settings

Saves the settings made for User 1 or User 2 mode.

 

 

 

 

Operation 55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedIntroduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior viewLamp cover External control panel Projector Controls and functionsTest Remote controlKeystone/Arrow buttons / Up Down Numeric buttons Operating the Laser pointerMute MIC/VOL +Replacing the remote control batteries Remote control effective rangePpr 15º Front Ceiling Positioning your projectorChoosing a location Front TableVertical Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm DiagonalConnection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceAbout the microphone input Playing sound through the projectorPage Operation OperationStarting up the projector DetailsFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageFollowing example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordChanging the password Correcting keystone Disabling the password functionTo correct keystoning at the bottom of the image Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageCreating your own startup screen To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Basic Menu operationMenu system Main menu Sub-menu OptionsEquivalent Lamp Hour Lamp Mode Normal/Economic Lamp SettingsAdvanced MessageAdvanced Network Description of each menu Display menu Picture menu Function Description Picture ModeTemperature Management Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsLock Settings Security DescriptionPanel Key BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampLamp cover loosens Remove the lamp cover from the projector Replacing the lampUse the handle to slowly pull the lamp out Projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsUnit mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Ceiling Mount screw M4 x 8 Max L = 8 mmSupported timing for PC input Timing chart1360 x Supported timing for Hdmi Hdcp inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users
Related manuals
Manual 2 pages 34.84 Kb
Top Page Image Contents