BenQ MX711, MX710 user manual Timing of replacing the lamp, Status Message

Page 62

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Go to http://lamp.benq.com for a replacement lamp.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 66 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

Install a new lamp for optimal performance. If the

Notice

projector is normally run with Economic selected

 

(See "Getting to know the lamp hour" on page 61),

Order Replacement Lamp

you may continue to operate the projector until

Lamp>XXXX Hours

the next hour lamp warning appears.

 

Press ENTER to dismiss the message.

Order a new lamp at lamp.benq.com

 

 

OK

 

 

It is strongly recommended that you replace the

Notice

lamp at this age. The lamp is a consumable item.

 

The lamp brightness diminishes with use. This is

Order Replacement Lamp

normal lamp behavior. You can replace the lamp

Lamp>XXXX Hours

whenever you notice that the brightness level has

 

significantly diminished.

Order a new lamp at lamp.benq.com

Press ENTER to dismiss the message.

OK

 

 

The lamp MUST be replaced before the projector

WARNING

will operate normally.

Out of Lamp Usage Time

Press ENTER to dismiss the message.

 

 

Replace lamp (refer to User Manual)

 

Then reset lamp timer

 

Order a new lamp at lamp.benq.com

 

OK

 

 

"XXXX" shown in the above messages are numbers that vary depending on different models.

62 Maintenance

Page 61 Page 63
Image 62
Page 61 Page 63
Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Lamp cover External control panel Projector exterior viewRear/lower side Controls and functions ProjectorKeystone/Arrow buttons / Up Down Remote controlTest MIC/VOL + Operating the Laser pointerMute Numeric buttonsPpr 15º Remote control effective rangeReplacing the remote control batteries Front Table Positioning your projectorChoosing a location Front CeilingScreen size Distance from screen mm Diagonal Projection dimensionsObtaining a preferred projected image size VerticalConnection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestPlaying sound through the projector About the microphone inputPage Details OperationStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure To correct keystoning at the bottom of the image Disabling the password functionCorrecting keystone Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Selection Description Setting the presentation timerTo cancel the timer, perform the following steps Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Utilizing FAQ functionRemote paging operations Hiding the imageOperating in a high altitude environment To activate the High Altitude ModeLocking control keys Creating your own startup screenAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system BasicMessage Lamp Mode Normal/Economic Lamp SettingsAdvanced Equivalent Lamp HourAdvanced Network Description of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function DescriptionSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground Settings Security DescriptionPanel Key LockBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternSystem Features ServiceCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Lamp cover loosens Remove the lamp cover from the projectorUse the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsCeiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input 1360 xTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users Weee directive
Related manuals
Manual 2 pages 34.84 Kb
Top Page Image Contents