BenQ MX710, MX711 Projector exterior view, Rear/lower side, Lamp cover External control panel

Page 9

Projector exterior view

Front/upper side
2	5
1	5
1
	6
3		7
	8	7
	8	9
4
		10

Rear/lower side

15 16

21 22 23

13 24

1.Lamp cover

2.External control panel

(See "Controls and functions" on page 10 for details.)

3.Vent (heated air exhaust)

4.Quick-release button

5.Top IR remote sensor

6.Focus and Zoom ring

7.Vent (cool air intake)

8.Speaker grill

9.Front IR remote sensor

10.Projection lens

11.AC power jack

12.Rear adjuster foot

13.Ceiling mount holes

14.Front adjuster foot

15.RS232 control port

16.RJ45 LAN input jack

17.USB ports

18.HDMI-input port

19.RGB signal output jack

20.RGB (PC)/Component Video (YPbPr/ YCbCr) signal input jack

21.S-Video input jack Video input jack

22.Audio (L/R) input jacks

23.Audio input jack Audio output jack Microphone jack

24.Kensington anti-theft lock slot

Introduction 9

Image 9

Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Rear/lower sideLamp cover External control panel Projector Controls and functionsRemote control TestKeystone/Arrow buttons / Up Down Mute Operating the Laser pointerMIC/VOL + Numeric buttonsRemote control effective range Replacing the remote control batteriesPpr 15º Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal VerticalConnection Connecting audio Connecting video source devicesTerminal name Terminal appearance BestAbout the microphone input Playing sound through the projectorPage Starting up the projector OperationDetails OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Correcting keystoneTo correct keystoning at the bottom of the image Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAdjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management To cancel the timer, perform the following steps Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-RightRemote paging operations Utilizing FAQ functionFreezing the image Hiding the imageLocking control keys To activate the High Altitude ModeOperating in a high altitude environment Creating your own startup screenAdjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring ToneCable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu system Menu operationMain menu Sub-menu Options BasicAdvanced Lamp Mode Normal/Economic Lamp SettingsMessage Equivalent Lamp HourAdvanced Network Description of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function DescriptionTimer System Setup Basic menu Function Description Quick AutoSettings SearchPanel Key Settings Security DescriptionBackground LockReset All System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampLamp cover loosens Remove the lamp cover from the projector Replacing the lampUse the handle to slowly pull the lamp out Projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmSupported timing for PC input Timing chart1360 x Supported timing for Hdmi Hdcp inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users Weee directive

Related manuals

Manual 2 pages 34.84 Kb