Rackmount Solutions VA 20000, VA 3000, VA 700, VA 10000, VA 6000 manual

Page 6

•Transport the unit only in suitable packaging (protect against jolts and shocks).

•If the equipment is moved indoors from a cold environment, condensation may occur. Before you place the equipment in service it must be absolutely dry. An acclimatization period of at least two hours is required.

•This equipment must be installed in an indoor, temperature controlled environment that is free of conductive contaminants. See chapter 10, “Active Tower and Rackmount Specifications” on page 22 for specific environmental limits.

•The Active equipment has a safety-tested power cable and may only be connected to a properly grounded receptacle.

•The switch (see chapter 2, “Display and Operation Elements (Active)” on page 3) does not isolate the device (UPS) from the mains. To isolate completely from the mains, the main switch must be switched off and the power plug disconnected.

CAUTION: Removing mains power may not remove power from the device (UPS) output. See instructions above to properly remove power from output.

•In case of interruption of the mains voltage, the integrated battery maintains the power supply to the connected equipment.

•Lay all cables so that nobody can stand on them or trip over them. When connecting the device to the power supply, follow the instructions in the chapter on “Active Installation and Commissioning” on page 11.

•No data transmission lines should be connected or disconnected during a thunderstorm.

•Make sure that no objects (e.g. pins, necklaces, paper clips, etc.) get inside the device.

•In emergencies (e.g. damaged case, controls or power cables, penetration of liquids or foreign matter) put the device into BYPASS, disconnect the power plug and contact Chloride Technical Services at 1-800-879-5011.

•Do not connect equipment that will overload the UPS (e.g. laser printers or vacuum cleaners) or demand DC-current (e.g. half-wave rectifiers or hair dryers).

•When cleaning the unit, follow the instructions in chapter 7, “Maintenance (Active)” on page 19.

•The sum of the leakage currents (protective conductor current) of the UPS and the connected devices must not exceed 3.5 mA for the types Active 700, 1000, 2000 and 3000.

Chloride Active UPS is UL listed under UL1778 for North American units.

2

Chloride Active and E-Series UPS User Manual

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Page Important Safety Instructions FCC ComplianceChloride Introduction Operational Characteristics E-Series Chloride Introduction Technical Support and Service ActiveSafety Notes Registering your Chloride Active UPSPage Display and Operation Elements Active Overload LoadFront Rear Active 700Active 2000 Active 3000 Rear ViewSafety Installation and operating notesActive Rackmount Series Type of Battery Packs Maximum Number of Packs Connection of a battery packBattery Cabinets Mechanical AttachmentUnit Rear View and Connections Active 700-19 and Active Active700-19Active 2000-19 and Active Active3000-19Active Installation and Commissioning Commissioning of an External Battery Cabinet External Battery PacksModel Cabinet Batteries Operational Characteristics Active Ready for Operation Check Self TestBattery Operation, Inverter On Mains Failure Modes of OperationNormal Operation, Inverter On Mains Available Bypass Operation, Inverter OFF Overload 140% Front Display Panel During Bypass Operation Overload 140%Description of the Interface Active Standard Interface COM aOptional Interface COM B Interface COM aPin Number Condition INV Shutdown Maintenance Active CleaningStorage Troubleshooting Active TroubleshootingProblem Possible Cause Action to Take Page Active Tower and Rackmount Specifications Chloride Active UPS North AmericaUPS Model Active Battery extensionSignals Mechanical DataUPS Model Active Connections Mains connections Load connectionActive Rackmount Technical Data for North American Models Operating DataBattery Lifetime Typical lifetime of the batteriesTechnical Support and Service E-Series Registering your Chloride E-Series UPSPage Display and Operation Elements E-Series Switch for at least 1 second. a tone sounds Series E61 and E101 E41 or E61Series E203 E81 or E101Series Installation and Commissioning Installation of the E-Series HardwiredPage Minimum Requirements for E-Series UPS Installation Lbs AwgWiring Diagram for the E101 Commissioning of the E-Series Starting Up the E-SeriesDryers, vacuum cleaners BPE61 Technical data of the connection cable E101 E203Self Test Modes of Operation Bypass Operation, Inverter OFF Overload 140% Description of the Interface E-Series Optional Interface COM B Emergency Power Off EPO Series Models E153X and E203X onlyMaintenance E-Series Troubleshooting E-Series Page Series Specifications Chloride E-Series UPS North AmericaBPE101 Weight lbs 337 894 Dimensions HxWxD in. mm E101XA E203XA E41XA E81 E153XA Connections Optional Power Distribution Units PDU available 4 -10 kVA Optional Power Distribution UnitsChloride Power Protection

VA 2000, VA 10000, VA 700, VA 3000, VA 20000 specifications

Rackmount Solutions offers a versatile lineup of VA series products designed for efficient power management in data centers and server environments. The VA 1000, VA 6000, VA 20000, VA 3000, and VA 700 models cater to a variety of power needs, ensuring reliable performance and robust features tailored to different operational demands.

Starting with the VA 1000, this model is compact yet powerful, providing up to 1000VA of power capacity. It features an LCD display that offers real-time information on power status, battery life, and load levels. The VA 1000 is equipped with pure sine wave output, ensuring compatibility with sensitive electronic equipment and providing protection against power surges. The unit is designed for easy integration into existing IT frameworks, with multiple outlets to accommodate various devices.

Next in the lineup, the VA 3000 model steps up the capacity to 3000VA. This unit excels in larger environments where higher power demands are common. It too features pure sine wave output and includes advanced battery management technology that optimizes performance and prolongs battery life. Its networking capabilities allow for remote management and monitoring through a web interface, providing IT managers with comprehensive control over their power infrastructure.

The VA 6000 doubles down on capacity, supporting robust applications with its 6000VA rating. It is equipped with advanced features such as surge protection, automatic voltage regulation, and a high-efficiency design that reduces energy consumption. Its modular design allows for ease of maintenance and upgrades, making it a cost-effective solution over time for growing data centers.

For the larger setups, the VA 20000 model stands out with a staggering 20000VA power capacity. Designed for high-demand applications, this unit incorporates features like redundancy and N+1 configurations to ensure uninterrupted power supply. Its scalable architecture makes it suitable for both small and large enterprises looking to future-proof their power infrastructure.

Lastly, the VA 700 model serves as an entry-level solution at 700VA. Ideal for small servers and networking devices, it offers essential features like battery monitoring and basic surge protection, making it a cost-effective choice for small business environments.

In summary, the Rackmount Solutions VA series, comprising models VA 1000, VA 3000, VA 6000, VA 20000, and VA 700, collectively offer a comprehensive suite of power management solutions. Their scalable designs, advanced technologies, and focus on efficiency make them ideal for a wide range of applications, from small offices to large data centers, ensuring reliability and performance in critical environments.
Top Page Image Contents