Mitsubishi Electronics XD95U Adjusting the projected image, Adjusting the projection angle

Page 21

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector:

ENGLISH

1.Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position.

2.Screw the rear adjuster foot to fine tune the horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

1

2

If the projector is not placed on a flat surface or the screen and the projector

are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 22 for details.

• Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

•Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the upper left corner of the screen for 3 seconds.

• The screen will be blank while AUTO is functioning.

•This function is only available when a PC signal (analog RGB) is selected.

Fine-tuning the image size and clarity

1.Adjust the projected image to the size that you need using the zoom ring.

2.Then sharpen the image by rotating the focus ring.

EN-21

Image 21

Contents XD95U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Kensington Lock Projector exterior viewFront/upper side External control panelProjector Controls and functionsFreeze Remote controlPull out the battery holder Remote control effective rangePositioning your projector Choosing a locationObtaining a preferred projected image size EN-12 Front projection Layout of the projectorStandard 169Connecting a computer Connecting Video source devicesConnection Connecting an S-Video source device Connecting a Component Video source deviceTo connect the projector to a Component Video source device To connect the projector to an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUse / to highlight the System Setup Basic menu Using the menusSetting a password Utilizing the password functionIf you forget the password Entering the password recall procedureChanging the password Switching input signalDisabling the password function Enter the old passwordAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Magnifying and searching for detailsAltering the images aspect ratio Selecting the aspect ratioPicture modes for different types of signals Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageFine-tuning the image quality in user modes Using Wall Color 3D Color ManagementPress MODE/ENTER and the 3D Color Management page displays Setting the presentation timer To cancel the timer, perform the following stepsHow to use the Timer On key? Hiding the image Setup Basic Panel Key Lock menu, and select On by pressingLocking control keys Freezing the imageOperating in a high altitude environment To activate the High Altitude ModePersonalizing the projector menu display Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options BasicAdvanced Description of each menu Auto Power Off Presentation TimerBlank Timer Timer ControllerSecurity Settings Setup menu Reset All SettingsCurrent System Status Care of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as LowLamp information Getting to know the lamp hourTiming of replacing the lamp Projector until the 2950 hour lamp warning appearsLamp has been in operation for 3000 hours Spare lamp for XD95U VLT-XD95LP Replacing the lampResetting the lamp timer Tighten the screw that secures the lampRestart the projector Down without the normal cooling down process IndicatorsProjector needs 90 seconds to cool down Please contact your dealer for assistanceTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Component-YPbPrinput Mitsubishi Electric Corporation