Mitsubishi Electronics XD95U user manual Magnifying and searching for details, Correcting keystone

Page 22

Correcting keystone

Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen.

To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps.

•Using the remote control

Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the top of the image. Press to correct keystoning at the bottom of the image.

• Using the OSD menu

1. Press MENU and then press / until the DISPLAY menu is highlighted.

2. Press to highlight Keystone and press MODE/ENTER. The Keystone correction page displays.

3.Press to correct keystoning at the top of the image or press to correct keystoning at the bottom of the image.

Press

/ .

Press / .

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

•Using the remote control

1.Press MAGNIFY +/- to display the Zoom bar.

2. Press MAGNIFY + to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need.

3. Use the directional arrows (, , , ) on the projector or remote control to navigate the picture.

4. To restore the picture to its original size, press AUTO. You can also press MAGNIFY -. When the key is pressed again, the picture is further reduced until it is restored to the original size.

•Using the OSD menu

1.Press MENU and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Magnify and press MODE/ENTER. The Zoom bar displays.

3.Repeat steps 2-4in the section of "Using the remote control" above. Or if you are using the projector control panel, continue to the following steps.

4.Press on the projector repeatedly to magnify the picture to a desired size.

5.To navigate the picture, press MODE/ENTER to switch to the panning mode and press the directional arrows (, , , ) to navigate the picture.

6.Use the directional arrows (, , , ) on the projector or remote control to navigate the picture.

7.To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/out functionality, and press

AUTO to restore the picture to its original size. You can also press repeatedly until it is restored to the original size.

The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details.

EN-22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents XD95U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Front/upper side Projector exterior viewKensington Lock External control panelControls and functions ProjectorRemote control FreezeRemote control effective range Pull out the battery holderChoosing a location Positioning your projectorObtaining a preferred projected image size EN-12 Standard Layout of the projectorFront projection 169Connecting Video source devices Connecting a computerConnection To connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Use / to highlight the System Setup Basic menuIf you forget the password Utilizing the password functionSetting a password Entering the password recall procedureDisabling the password function Switching input signalChanging the password Enter the old passwordAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio Altering the images aspect ratioSetting the User 1/User 2 mode Selecting a picture modePicture modes for different types of signals Optimizing the imageFine-tuning the image quality in user modes 3D Color Management Using Wall ColorPress MODE/ENTER and the 3D Color Management page displays To cancel the timer, perform the following steps Setting the presentation timerHow to use the Timer On key? Locking control keys Setup Basic Panel Key Lock menu, and select On by pressingHiding the image Freezing the imagePersonalizing the projector menu display To activate the High Altitude ModeOperating in a high altitude environment Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced Description of each menu Blank Timer Presentation TimerAuto Power Off Timer ControllerSetup menu Reset All Settings Security SettingsCurrent System Status Maintenance Care of the projectorLamp information Setting Lamp mode as LowSetting Auto Power Off Getting to know the lamp hourProjector until the 2950 hour lamp warning appears Timing of replacing the lampLamp has been in operation for 3000 hours Replacing the lamp Spare lamp for XD95U VLT-XD95LPTighten the screw that secures the lamp Resetting the lamp timerRestart the projector Projector needs 90 seconds to cool down IndicatorsDown without the normal cooling down process Please contact your dealer for assistanceTroubleshooting Specifications Projector specificationsDimensions Timing chartSupported timing for Component-YPbPrinput Mitsubishi Electric Corporation
Top Page Image Contents