Mitsubishi Electronics XD95U user manual Specifications, Projector specifications

Page 42

Specifications

Projector specifications

All specifications are subject to change without notice.

General

Product name	DLPTM DATA Projector
Model name	XD95U

Optical

Resolution	1024 x 768 XGA

Display system	1-CHIP DMD

Lens F/Number	F = 2.56 to 2.67, f = 21.36 to 23.45 mm

Lamp	200 W lamp

Electrical

Power supply	AC100–240V, 2.9 A, 50/60 Hz (Automatic)

Power consumption	285 W (Max)

Mechanical

Dimensions	190 mm (W) x 84.2 mm (H) x 205.2 mm (D)

Weight	3.3 lbs (1.5 Kg)

Input terminal

Computer input

RGB input	D-Sub 15-pin (female) x 1

Video signal input

S-VIDEO	Mini DIN 4-pin port x 1

VIDEO	RCA jack x 1

SD/HDTV signal input	Analog – D-Sub <–> Component RCA jack x 3
	(through RGB input)
Control terminal

RS-232 serial control	8 pin x 1

Environmental requirements

Operating temperature	0°C–35°C at sea level

Operating relative humidity	10%–90% (without condensation)

Operating altitude	• 0–1499 m at 0°C–35°C
	• 1500–3000 m at 0°C–30°C (with High Altitude Mode on)

EN-42

Image 42

Contents XD95U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Front/upper side Projector exterior viewKensington Lock External control panelControls and functions ProjectorRemote control FreezeRemote control effective range Pull out the battery holderPositioning your projector Choosing a locationObtaining a preferred projected image size EN-12 Standard Layout of the projectorFront projection 169Connecting a computer Connecting Video source devicesConnection To connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Use / to highlight the System Setup Basic menuIf you forget the password Utilizing the password functionSetting a password Entering the password recall procedureDisabling the password function Switching input signalChanging the password Enter the old passwordAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio Altering the images aspect ratioSetting the User 1/User 2 mode Selecting a picture modePicture modes for different types of signals Optimizing the imageFine-tuning the image quality in user modes Using Wall Color 3D Color ManagementPress MODE/ENTER and the 3D Color Management page displays Setting the presentation timer To cancel the timer, perform the following stepsHow to use the Timer On key? Locking control keys Setup Basic Panel Key Lock menu, and select On by pressingHiding the image Freezing the imagePersonalizing the projector menu display To activate the High Altitude ModeOperating in a high altitude environment Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced Description of each menu Blank Timer Presentation TimerAuto Power Off Timer ControllerSecurity Settings Setup menu Reset All SettingsCurrent System Status Maintenance Care of the projectorLamp information Setting Lamp mode as LowSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Projector until the 2950 hour lamp warning appearsLamp has been in operation for 3000 hours Replacing the lamp Spare lamp for XD95U VLT-XD95LPResetting the lamp timer Tighten the screw that secures the lampRestart the projector Projector needs 90 seconds to cool down IndicatorsDown without the normal cooling down process Please contact your dealer for assistanceTroubleshooting Specifications Projector specificationsDimensions Timing chartSupported timing for Component-YPbPrinput Mitsubishi Electric Corporation