Mitsubishi Electronics XD95U Quick Auto Search, Presentation Timer, Language, Auto Power Off

Page 33

FUNCTION

(default setting/value)

3.

 

SOURCE menu

Quick Auto Search

 

 

(On)

 

Presentation Timer

 

(Off)

4.

Language

(English)

SYSTEM

Auto Power Off

 

Projector Position

SETUP:

(Front Table)

(Disable)

 

 

Blank Timer

Basic

(Disable)

Panel Key Lock

 

menu

(Off)

Timer Controller

 

(Disable)

 

Splash Screen

 

(MITSUBISHI logo)

 

Quick Cooling

5.

(Off)

 

SYSTEM

High Altitude Mode

 

SETUP:Advanced

(Off)

Menu Settings

 

menu

Lamp Settings

 

DESCRIPTION (default setting/value)

See "Switching input signal" on page 20 for details.

Reminds the presenter to finish the presentation within a certain time frame. See "Setting the presentation timer" on page 27 for details.

Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 18 for details.

See "Choosing a location" on page 11 for details.

Allows the projector to turn off automatically if no input signal is detected after a set period of time. See "Setting Auto Power Off" on page 36 for details.

Sets the image blank time when the Blank feature is activated, once elapsed the image will return to the screen. See "Hiding the image" on page 28 for details.

Disables or enables all panel key functions except II Power on the projector and keys on the remote control. See "Locking control keys" on page 28 for details.

Sets the auto-shutdown timer. The timer can be set to a value between 30 minutes and 12 hours.

Allows you to select which logo screen will display during projector start-up. Three options are available: MITSUBISHI logo, Black screen, or Blue screen.

Selecting On enables the function and the projector cooling time will be shortened to a few seconds.

If you attempt to restart the projector right after the quick cooling process, it may not be turned on successfully and will rerun its cooling fans.

A mode for operation in high altitude areas. See "Operating in a high altitude environment" on page 29 for details.

Menu display time (15 sec)

Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments.

Menu position (Center)

Sets the On-Screen Display (OSD) menu position.

Lamp mode (Standard)

See "Setting Lamp mode as Low" on page 36 for details.

Reset lamp timer

See "Resetting the lamp timer" on page 39 for details.

Equivalent lamp hour

See "Getting to know the lamp hour" on page 36 for details on how the total lamp hour is calculated.

ENGLISH

EN-33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents XD95U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Kensington Lock Projector exterior viewFront/upper side External control panelProjector Controls and functionsFreeze Remote controlPull out the battery holder Remote control effective rangePositioning your projector Choosing a locationObtaining a preferred projected image size EN-12 Front projection Layout of the projectorStandard 169Connecting a computer Connecting Video source devicesConnection Connecting an S-Video source device Connecting a Component Video source deviceTo connect the projector to a Component Video source device To connect the projector to an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUse / to highlight the System Setup Basic menu Using the menusSetting a password Utilizing the password functionIf you forget the password Entering the password recall procedureChanging the password Switching input signalDisabling the password function Enter the old passwordAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Magnifying and searching for detailsAltering the images aspect ratio Selecting the aspect ratioPicture modes for different types of signals Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageFine-tuning the image quality in user modes Using Wall Color 3D Color ManagementPress MODE/ENTER and the 3D Color Management page displays Setting the presentation timer To cancel the timer, perform the following stepsHow to use the Timer On key? Hiding the image Setup Basic Panel Key Lock menu, and select On by pressingLocking control keys Freezing the imageOperating in a high altitude environment To activate the High Altitude ModePersonalizing the projector menu display Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options BasicAdvanced Description of each menu Auto Power Off Presentation TimerBlank Timer Timer ControllerSecurity Settings Setup menu Reset All SettingsCurrent System Status Care of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as LowLamp information Getting to know the lamp hourTiming of replacing the lamp Projector until the 2950 hour lamp warning appearsLamp has been in operation for 3000 hours Spare lamp for XD95U VLT-XD95LP Replacing the lampResetting the lamp timer Tighten the screw that secures the lampRestart the projector Down without the normal cooling down process IndicatorsProjector needs 90 seconds to cool down Please contact your dealer for assistanceTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Component-YPbPrinput Mitsubishi Electric Corporation
Top Page Image Contents