Mitsubishi Electronics XD95U Tighten the screw that secures the lamp, Restart the projector

Page 39

7.Tighten the screw that secures the lamp.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

8. Ensure the handle is fully laid flat and locked in place.

9.As shown in the figure, replace the lamp cover on the projector.

10. Tighten the screws that secure the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screws.

11. Restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

12.After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced > Lamp Settings menu. Press

MODE/ENTER. The Lamp Settings page displays. Press to highlight Reset lamp timer and press MODE/ENTER. A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to '0'.

• Do not reset if the lamp is not new or replaced as this could cause damage.

•This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. (For US only).

ENGLISH

EN-39

Image 39

Contents XD95U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada External control panel Projector exterior viewKensington Lock Front/upper sideProjector Controls and functionsFreeze Remote controlPull out the battery holder Remote control effective rangePositioning your projector Choosing a locationObtaining a preferred projected image size EN-12 169 Layout of the projectorFront projection StandardConnecting a computer Connecting Video source devicesConnection To connect the projector to an S-Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to a Component Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUse / to highlight the System Setup Basic menu Using the menusEntering the password recall procedure Utilizing the password functionSetting a password If you forget the passwordEnter the old password Switching input signalChanging the password Disabling the password functionFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsAltering the images aspect ratio Selecting the aspect ratioOptimizing the image Selecting a picture modePicture modes for different types of signals Setting the User 1/User 2 modeFine-tuning the image quality in user modes Using Wall Color 3D Color ManagementPress MODE/ENTER and the 3D Color Management page displays Setting the presentation timer To cancel the timer, perform the following stepsHow to use the Timer On key? Freezing the image Setup Basic Panel Key Lock menu, and select On by pressingHiding the image Locking control keysShutting down the projector To activate the High Altitude ModeOperating in a high altitude environment Personalizing the projector menu displayBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Description of each menu Timer Controller Presentation TimerAuto Power Off Blank TimerSecurity Settings Setup menu Reset All SettingsCurrent System Status Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as LowSetting Auto Power Off Lamp informationTiming of replacing the lamp Projector until the 2950 hour lamp warning appearsLamp has been in operation for 3000 hours Spare lamp for XD95U VLT-XD95LP Replacing the lampResetting the lamp timer Tighten the screw that secures the lampRestart the projector Please contact your dealer for assistance IndicatorsDown without the normal cooling down process Projector needs 90 seconds to cool downTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Component-YPbPrinput Mitsubishi Electric Corporation