Mitsubishi Electronics user manual Replacing the lamp, Spare lamp for XD95U VLT-XD95LP

Page 38

Replacing the lamp

Spare lamp for XD95U: VLT-XD95LP

•To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.

•To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

•To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.

•To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.

•This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.

•To assure optimal performance from the projector, it is recommended that you purchase a Mitsubishi projector lamp for lamp replacement.

1.Turn the power off and disconnect the projector from the wall

socket. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2. Turn the projector over. Then loosen the screws on the lamp cover.

3.Remove the lamp cover from the projector.

• Do not turn the power on with the lamp cover removed.

• Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

4.Loosen the screw that secures the lamp.

5.Lift the handle so that it stands up. Use the handle to slowly pull the

lamp out of the projector.

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

• Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

6.As shown in the figure, lower the new lamp into the lamp

compartment while aligning the lamp with the holes in the lamp compartment. Make sure it fits in the projector.

EN-38

Image 38

Contents XD95U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Front/upper side Projector exterior viewKensington Lock External control panelControls and functions ProjectorRemote control FreezeRemote control effective range Pull out the battery holderObtaining a preferred projected image size Positioning your projectorChoosing a location EN-12 Standard Layout of the projectorFront projection 169Connection Connecting a computerConnecting Video source devices To connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Use / to highlight the System Setup Basic menuIf you forget the password Utilizing the password functionSetting a password Entering the password recall procedureDisabling the password function Switching input signalChanging the password Enter the old passwordAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio Altering the images aspect ratioSetting the User 1/User 2 mode Selecting a picture modePicture modes for different types of signals Optimizing the imageFine-tuning the image quality in user modes Press MODE/ENTER and the 3D Color Management page displays Using Wall Color3D Color Management How to use the Timer On key? Setting the presentation timerTo cancel the timer, perform the following steps Locking control keys Setup Basic Panel Key Lock menu, and select On by pressingHiding the image Freezing the imagePersonalizing the projector menu display To activate the High Altitude ModeOperating in a high altitude environment Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced Description of each menu Blank Timer Presentation TimerAuto Power Off Timer ControllerCurrent System Status Security SettingsSetup menu Reset All Settings Maintenance Care of the projectorLamp information Setting Lamp mode as LowSetting Auto Power Off Getting to know the lamp hourLamp has been in operation for 3000 hours Timing of replacing the lampProjector until the 2950 hour lamp warning appears Replacing the lamp Spare lamp for XD95U VLT-XD95LPRestart the projector Resetting the lamp timerTighten the screw that secures the lamp Projector needs 90 seconds to cool down IndicatorsDown without the normal cooling down process Please contact your dealer for assistanceTroubleshooting Specifications Projector specificationsDimensions Timing chartSupported timing for Component-YPbPrinput Mitsubishi Electric Corporation