Mitsubishi Electronics XD95U user manual Indicators, Down without the normal cooling down process

Page 40

Indicators

	Light			Status & Description

	Power	Temp	Lamp

	Power events

	Orange	Off	Off	Stand-by mode

	Green	Off	Off	Powering up
	Flashing	Off	Off	Powering up
	Flashing
	Green	Off	Off	Normal operation

	Orange			• The projector needs 90 seconds to cool down as it was abnormally shut
	Orange	Off	Red	down without the normal cooling down process.
	Flashing	Off	Red	down without the normal cooling down process.
	Flashing			• The projector needs to cool for 90 seconds after the power is turned off.


	Orange	Off	Off	The projector has shutdown automatically. If you try to re-start the projector, it
	Flashing	Off	Off	will shutdown again. Please contact your dealer for assistance.
	Flashing

	Lamp events

	Orange	Off	Red	The projector has shutdown automatically. If you try to re-start the projector, it
	Flashing	Off	Red	will shutdown again. Please contact your dealer for assistance.
	Flashing
	Off	Off	Red	• The projector needs 90 seconds to cool down.
	Off	Off	Red	• Please contact your dealer for assistance.
				• Please contact your dealer for assistance.

	Thermal events

	Off	Red	Off

	Off	Red	Red

	Off	Red	Green

	Red	Red	Red

	Red	Red	Green	The projector has shutdown automatically. If you try to re-start the projector, it

	Green	Red	Red
	Green	Red	Red	will shutdown again. Please contact your dealer for assistance.

	Green	Red	Green

	Orange	Red	Red

	Orange	Red	Green

	Off	Green	Red

	Off	Green	Green

EN-40

Image 40

Contents XD95U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Projector exterior view Kensington LockFront/upper side External control panelControls and functions ProjectorRemote control FreezeRemote control effective range Pull out the battery holderChoosing a location Positioning your projectorObtaining a preferred projected image size EN-12 Layout of the projector Front projectionStandard 169Connecting Video source devices Connecting a computerConnection Connecting a Component Video source device Connecting an S-Video source deviceTo connect the projector to a Component Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Use / to highlight the System Setup Basic menuUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureSwitching input signal Changing the passwordDisabling the password function Enter the old passwordAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio Altering the images aspect ratioSelecting a picture mode Picture modes for different types of signalsSetting the User 1/User 2 mode Optimizing the imageFine-tuning the image quality in user modes 3D Color Management Using Wall ColorPress MODE/ENTER and the 3D Color Management page displays To cancel the timer, perform the following steps Setting the presentation timerHow to use the Timer On key? Setup Basic Panel Key Lock menu, and select On by pressing Hiding the imageLocking control keys Freezing the imageTo activate the High Altitude Mode Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options BasicAdvanced Description of each menu Presentation Timer Auto Power OffBlank Timer Timer ControllerSetup menu Reset All Settings Security SettingsCurrent System Status Maintenance Care of the projectorSetting Lamp mode as Low Setting Auto Power OffLamp information Getting to know the lamp hourProjector until the 2950 hour lamp warning appears Timing of replacing the lampLamp has been in operation for 3000 hours Replacing the lamp Spare lamp for XD95U VLT-XD95LPTighten the screw that secures the lamp Resetting the lamp timerRestart the projector Indicators Down without the normal cooling down processProjector needs 90 seconds to cool down Please contact your dealer for assistanceTroubleshooting Specifications Projector specificationsDimensions Timing chartSupported timing for Component-YPbPrinput Mitsubishi Electric Corporation