Mitsubishi Electronics XD95U user manual Dimensions, Timing chart

Page 43

Dimensions

190 mm (W) x 84.2 mm (H) x 205.2 mm (D)

ENGLISH

205.2

84.2

190
47	51.7

Timing chart

Supported timing for PC input

Resolution	Mode	Refresh rate (Hz)	Horizontal	Clock (MHz)
Resolution	Mode	Refresh rate (Hz)	frequency (kHz)	Clock (MHz)
			frequency (kHz)
720 x 400	720 x 400_70	70.087	31.469	28.3221
	VGA_60	59.940	31.469	25.175
640 x 480	VGA_72	72.809	37.861	31.500
640 x 480	VGA_75	75.000	37.500	31.500
	VGA_75	75.000	37.500	31.500
	VGA_85	85.008	43.269	36.000
	SVGA_60	60.317	37.879	40.000
800 x 600	SVGA_72	72.188	48.077	50.000
800 x 600	SVGA_75	75.000	46.875	49.500
	SVGA_75	75.000	46.875	49.500
	SVGA_85	85.061	53.674	56.250
	XGA_60	60.004	48.363	65.000
1024 x 768	XGA_70	70.069	56.476	75.000
1024 x 768	XGA_75	75.029	60.023	78.750
	XGA_75	75.029	60.023	78.750
	XGA_85	84.997	68.667	94.500
1280 x 1024	SXGA3_60	60.020	63.981	108.00
1280 x 800	WXGA_60	59.810	49.702	83.500
1280 x 960	1280 x 960_60	60.000	60.000	108.00
640 x 480@67Hz	MAC13	66.667	35.000	30.240
832 x 624@75Hz	MAC16	74.546	49.722	57.280
1024 x 768@75Hz	MAC19	75.020	60.241	80.000
1152 x 870@75Hz	MAC21	75.06	68.68	100.00

EN-43

Image 43

Contents XD95U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada External control panel Projector exterior viewKensington Lock Front/upper sideProjector Controls and functionsFreeze Remote controlPull out the battery holder Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size EN-12 169 Layout of the projectorFront projection StandardConnecting Video source devices Connecting a computerConnection To connect the projector to an S-Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to a Component Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUse / to highlight the System Setup Basic menu Using the menusEntering the password recall procedure Utilizing the password functionSetting a password If you forget the passwordEnter the old password Switching input signalChanging the password Disabling the password functionFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsAltering the images aspect ratio Selecting the aspect ratioOptimizing the image Selecting a picture modePicture modes for different types of signals Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Using Wall ColorPress MODE/ENTER and the 3D Color Management page displays To cancel the timer, perform the following steps Setting the presentation timerHow to use the Timer On key? Freezing the image Setup Basic Panel Key Lock menu, and select On by pressingHiding the image Locking control keysShutting down the projector To activate the High Altitude ModeOperating in a high altitude environment Personalizing the projector menu displayBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Description of each menu Timer Controller Presentation TimerAuto Power Off Blank TimerSetup menu Reset All Settings Security SettingsCurrent System Status Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as LowSetting Auto Power Off Lamp informationProjector until the 2950 hour lamp warning appears Timing of replacing the lampLamp has been in operation for 3000 hours Spare lamp for XD95U VLT-XD95LP Replacing the lampTighten the screw that secures the lamp Resetting the lamp timerRestart the projector Please contact your dealer for assistance IndicatorsDown without the normal cooling down process Projector needs 90 seconds to cool downTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Component-YPbPrinput Mitsubishi Electric Corporation