Microsoft MN-500 Regulatory Information, United States Radio and TV Interference Regulations

Page 61

Regulatory Information

United States Radio and TV Interference Regulations

This device complies with Part 15 of the U.S. Federal Communications Commission (FCC) rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The Microsoft hardware device(s) that accompanies this software can radiate radio frequency (RF) energy. If not installed and used in strict accordance with the instructions given in this User’s Guide, the device may cause harmful interference with other radio-communications devices (for example AM/FM radios, televisions, baby monitors, cordless phones, etc.). Any cable that is connected to the device must be a shielded cable that is properly grounded. There is, however, no guarantee that RF interference will not occur in a particular installation.

Your Microsoft hardware device has been tested, and it complies with the limits for a Class B digital device in accordance with the specifications in Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful RF interference in a residential installation.

To determine if your hardware device is causing interference to other radio-communications devices, disconnect the device from your computer. If the interference stops, it was probably caused by the device. If the interference continues after you disconnect the hardware device, turn the computer off and then on again. If the interference stopped when the computer was off, check to see if one of the input/output (I/O) devices or one of the computer's internal accessory boards is causing the problem. Disconnect the I/O devices one at a time and see if the interference stops.

If this hardware device does cause interference, try the following measures to correct it:

ORelocate the antenna of the other radio-communications device (for example AM/FM Radios, televisions, baby monitors, cordless phones, etc.) until the interference stops.

OMove the hardware device farther away from the radio or TV, or move it to one side or the other of the radio or TV.

OPlug the computer into a different power outlet so that the hardware device and radio or TV are on different circuits controlled by different circuit breakers or fuses.

OIf necessary, ask your computer dealer or an experienced radio-TV technician for more suggestions. You may find helpful information about interference issues at the following FCC Web site: http://www.fcc.gov/cgb/consumerfacts/interference.html, or call the FCC at 1-888-CALL FCC to request from the operator “Interference and Telephone Interference” fax sheets.

Note

Any changes or modifications not expressly approved by Microsoft could void the user’s authority to operate this device.

For use with UL Listed and GS approved personal computers. Not intended for use in machinery or industrial applications. Tested to comply with FCC Standards. For home and office use.

Model Numbers: MN-100, MN-110, MN-120, MN-130, MN-150, MN-500, MN-510, MN-520, MN-700, MN-720, MN-730

In addition, the following model numbers have been approved under FCC certification rather than under the FCC Declaration of Conformity Process:

MN-500, FCC ID: HEDACC300568; MN-510, FCC ID: HEDACCWN330168; MN-520, FCC ID: HEDACC3501D68;

MN-700, FCC ID: C3KMN700; MN-720, FCC ID: C3KMN720; MN-730, FCC ID: C3KMN730

Microsoft Corporation One Microsoft Way Redmond, WA 98052-6399.

(800)426-9400 (United States)

(800)933-4750 (Canada)

Canadian Radiocommunication Regulations

This Class B digital apparatus complies with Canadian ICES-003.

The term “IC:” before the certification/registration number only signifies that the Industry Canada technical specifications were met.

Cet appareil numérique de la classe B est conforme aux normes NMB-003 du Canada.

L’expression «IC:» avant le numéro d’homologation/enregistrement signifie seulement que les spécifications techniques d’Industrie Canada ont été respectées.

MN-500, IC: 3857A-300568; MN-510, IC: 3857A-330168; MN-520, IC: 3857A-350168;

MN-700, IC: 3048A-MN700; MN-720, IC: 3048A-MN720; MN-730, IC: 3048A-MN730

Appendixes 55

Image 61
Contents Page Avertissement Contents View Status View Network Devices Contents Page Introduction About Your Wireless Base StationBase Station Ports, Status Lights, and the Reset Button UPnP Standards and Your Wireless Base StationIntroduction Resetting the Base Station Using the Base Station StandRestoring Factory Default Settings Placement of Wireless Components About Wireless Radio ConnectionsUnderstanding Wireless Transmission Standards Adjusting the AntennaEthernet Cables About Wired Ethernet ConnectionsStraight-Through Ethernet Cable Which Cable Should You Use?Crossover Ethernet Cable Setup Gather Components, Tools, and Information Typical SetupThis User’s Guide Run the Setup WizardConnect the Base Station Test Your Network Configure the Base StationWhat’s Next? To set up the base station wirelessly Setting Up the Base Station WirelesslyCustom setup Establish the Base Station Password Base Station SetupOpen the Base Station Management Tool Establish Your Internet Settings Establish Your Wireless Security Settings Establish Your Wireless SettingsConfigure Your Computer Customize Network SettingsTest Your Internet Connection Network activities Logging on to Your Network Using an Internet Connection over a NetworkTo log off and log back on to your network To start the Broadband Network Utility Using the Broadband Network UtilityTo refresh the Network Devices list To remove an inactive device from the Network Devices listMake your files and folders available to the network Using Files and Folders over a NetworkTo share a folder or drive on your computer in Windows XP To share a folder or drive on your computer in Windows Access shared files Using a Printer over a NetworkTo access shared files on other computers About Reading E-Mail Messages on a Network Using Other Peripheral Devices over a NetworkPlaying Games on Your Network and on the Internet View Status Monitoring Your NetworkView Network Devices To refresh the network device listUpdating Software, Drivers, and Firmware To upgrade software, drivers, or firmwareMaking Your Network More Secure Help Protect Your Network from Computer VirusesHelp Protect Your Network from Hackers Help Protect Your Network from Unauthorized AccessPage Setup and Hardware Problems TroubleshootingIf your base station is connected wirelessly Setup does not recognize my wireless base stationIf your base station is connected with an Ethernet cable Troubleshooting To clone a MAC address Troubleshooting Can’t stay connected to my wireless network Network and Internet ProblemsTo disable 802.1x authentication in Windows XP Troubleshooting Page Troubleshooting My network is slow Troubleshooting Page Cant print to a networked printer Printing and File Sharing IssuesPage Troubleshooting Click OK to save the changes To determine which connection type your ISP provides Internet Connection TypeDynamic IP Dhcp Settings General Internet SettingsTo locate your Internet settings Host NameTo locate your static IP address settings Windows XP Static IP SettingsTo locate your static IP address settings Windows Workgroup Name PPPoE SettingsTo determine your workgroup name in Windows XP or Windows Wireless Security Settings Wireless Network NameTo determine your workgroup name in Windows Me and Windows Technical Support Options Getting HelpUnited States Radio and TV Interference Regulations Regulatory InformationCanadian Radiocommunication Regulations Base Station Technical SpecificationsSystem Requirements END-USER License Agreement for Microsoft Software General Provisions Limited Warranty Contrat DE Licence Utilisateur Final Pour Logiciel Microsoft Dispositions Générales Garantie Limitée Page Glossary Page Glossary Page Glossary Page Index Interference Index Typical Setup base station, 9 preparing for My Network Settings