VocoPro DTX-9909K owner manual Getting Connected, Connecting Speakers, Preparing the Speaker Cable

Page 12

Getting Connected

Connecting Speakers

The Speaker Terminals are located on the rear panel. There are two FRONT terminals, one CENTER terminal, Two SUR- ROUND terminals and two SURR BACK (surround back) terminals. Be sure to connect the left channel (L), right channel (R), “+” (red) and “--” (black) properly.

��������������������

����

Caution

If using 4speakers, be sure to set the DTX- 9909K’s speaker impedance setting to 4before using. If using 8speakers, make sure it is set to 8. The speaker impedance switch is located on the rear panel.

 

 

 

��������

 

 

 

�������������

 

 

 

��������������

 

 

 

���������

 

 

 

����������������������������

 

 

 

���������

������

��

���������

������

Preparing the Speaker Cable

You can either used an exposed speaker wire or Banana Plug speaker cable.

Exposed Speaker Wire

1. Remove approximately 3/8” (10mm) of insulation

����

2. Twist the exposed wires together to prevent short circuits

4.Insert the bare wire

5.Tighten the knob until the wire is secure

����������������

Before connecting the speakers, make sure that the DTX- 9909K is disconnected from the power source.

Do not let the bare speaker wires touch each other or another metal part of this unit. This could damage the DTX-9909K and/or the speakers.

12

Image 12
Contents DTX-9909K Page Table of Contents Page Listening for a lifetime Safety Instructions Welcome Features FeaturesConnections Contents Technical Specifi cations Test conditionExcess noise 98.0MHz DBu Sensitivity 106.0MHz Signal noise ratio About the Remote Control Connecting the Power CableInstalling Batteries in the Remote Control Battery ReplacementConnecting Speakers Getting ConnectedPreparing the Speaker Cable Connecting to the Front speaker terminals Connecting to the Center speaker terminalsConnecting to the Surround speaker terminals Connecting to the Surround Back speaker termi- nalsGetting Connected Connecting to the DTX-9909K’s Inputs Connecting a DVD Player with RCA Audio and Video OutputsChoosing a Video Output Selecting the Correct input channelConnecting to a TV using the RCA Video yellow Output Connecting a DVD Player Video using S-Video Inputs Connecting to a TV / Video Monitor using the S- Video OutputGetting Connected Connecting a CD or Tape Player audio-only Connecting a Player with Digital Optical Audio Out Puts Digital Audio OptionsMatching up the Correct Video Input Connecting a Player with Digital Coaxial Audio Out Puts Connecting Microphones Connecting HeadphonesAdjusting the Microphone Volume Headphone NotesAbout Karaoke Mode and Music Mode Descriptions and FunctionsDescriptions and Functions Descriptions and Functions Rear Panel Descriptions and Functions Descriptions and Functions Descriptions and Functions Remote Control Descriptions and Functions Descriptions and Functions Display Basic Functions Connecting the Antennas AM/FM Tuner OperationsOperating the Auto Tuner Preset Stations Automatic Preset StoringManually Presetting Stations Retrieving Preset StationsSpeaker Settings Menu Speaker Settings MenuAvailable Speaker Settings Accessing the Speaker Settings MenuAdjusting Speaker Output Levels Choices 0/0, S/0, L/0, S/S, and L/LChoices Y yes, N none Level range -10dB to +10dBSpeaker Tone Settings Karaoke Mode Karaoke Mode Settings MenuDelay Time Range 0ms -- 250ms Bass Tone Range -10dB -- +10dBTreble Tone Range -10dB -- +10dB Repeat Range 0dB -- 80dBReverb Volume Range 0 Reverb Time Range 0Feedback Time Range 0ms -- 80ms Choices L R, C, L R C, SL SR L R C, and SL SR CSurround Sound Setup ReferencePlayback Mode Display Abbrevations and Full Working Na mes Troubleshooting Problem CauseTroubleshooting Resetting the DTX-9909K Delay IndexCIN Page