VocoPro DTX-9909K owner manual Basic Functions

Page 34

Basic Functions

Turning the Power On and Off

1.Press the POWER button on the front panel to turn the power on. “Initializing........” will appear in the display panel. After three seconds of initializing, the unit will be ready to operate

2.Press the POWER button on the front panel again to turn the receiver off

Turning Standby On and Off

1.When the receiver is on, press the button on the remote control to enter Standby mode. “POWER OFF....” will appear in the display panel.

2.Press the button on the remote control again to exit Standby mode. “Initializing........” will appear in the display panel. After three seconds of initializing, the unit will be ready to operate

NOTE: In Standby mode, the DTX-9909K con- sumes a small amount of power in order to receive infrared signals from the remote control.

Selecting an Input Channel

Available Input channels

• DVD

• TAPE

• AUX1

• OPT1*

• AUX2

• OPT2*

• AUX3

• COX1*

• CD

• COX2*

• TV

• COX3*

• TUNER

• 7.1 CH*

Front Panel

Input/Adjust control knob - Use this knob to cycle through the available input channels when the DTX-9909K is in Music Mode. The DTX-9909K is in Music Mode whenever a microphone is NOT connected to either of the microphone inputs.

Input button - Press this button to cycle through the available input channels.

Adjusting the Music Volume

Adjust the master music volume using the VOLUME control on the front panel. Turn the VOLUME control clockwise to raise the volume and counter-clockwise to lower the volume.

*Digital channels are not available in Zone 2. Zone 2 is reserved for analog output

Remote Control - Use the Input Select buttons to select an input channel.

Adjusting the Master Microphone Volume

When there is one or more microphones connected to the microphone input(s) on the front panel, a djust the master microphone volume using the INPUT/ADJUST control on the front panel. Turn the control clockwise to raise the volume and counter-clockwise to lower the volume.

NOTE: At least one microphone must be con- nected to a microphone input for INPUT/ADJUST control to adjust the microphone volume.

34

Image 34
Contents DTX-9909K Page Table of Contents Page Listening for a lifetime Safety Instructions Welcome Features FeaturesConnections Contents Test condition Technical Specifi cationsExcess noise 98.0MHz DBu Sensitivity 106.0MHz Signal noise ratio Installing Batteries in the Remote Control About the Remote ControlConnecting the Power Cable Battery ReplacementGetting Connected Connecting SpeakersPreparing the Speaker Cable Connecting to the Surround speaker terminals Connecting to the Front speaker terminalsConnecting to the Center speaker terminals Connecting to the Surround Back speaker termi- nalsGetting Connected Choosing a Video Output Connecting to the DTX-9909K’s InputsConnecting a DVD Player with RCA Audio and Video Outputs Selecting the Correct input channelConnecting to a TV using the RCA Video yellow Output Connecting a DVD Player Video using S-Video Inputs Connecting to a TV / Video Monitor using the S- Video OutputGetting Connected Connecting a CD or Tape Player audio-only Digital Audio Options Connecting a Player with Digital Optical Audio Out PutsMatching up the Correct Video Input Connecting a Player with Digital Coaxial Audio Out Puts Adjusting the Microphone Volume Connecting MicrophonesConnecting Headphones Headphone NotesAbout Karaoke Mode and Music Mode Descriptions and FunctionsDescriptions and Functions Descriptions and Functions Rear Panel Descriptions and Functions Descriptions and Functions Descriptions and Functions Remote Control Descriptions and Functions Descriptions and Functions Display Basic Functions AM/FM Tuner Operations Connecting the AntennasOperating the Auto Tuner Manually Presetting Stations Preset StationsAutomatic Preset Storing Retrieving Preset StationsAvailable Speaker Settings Speaker Settings MenuSpeaker Settings Menu Accessing the Speaker Settings MenuChoices Y yes, N none Adjusting Speaker Output LevelsChoices 0/0, S/0, L/0, S/S, and L/L Level range -10dB to +10dBSpeaker Tone Settings Karaoke Mode Karaoke Mode Settings MenuTreble Tone Range -10dB -- +10dB Delay Time Range 0ms -- 250msBass Tone Range -10dB -- +10dB Repeat Range 0dB -- 80dBFeedback Time Range 0ms -- 80ms Reverb Volume Range 0Reverb Time Range 0 Choices L R, C, L R C, SL SR L R C, and SL SR CSurround Sound Setup ReferencePlayback Mode Display Abbrevations and Full Working Na mes Troubleshooting Problem CauseTroubleshooting Resetting the DTX-9909K Delay IndexCIN Page