Mitsumi electronic HD8000 user manual Setting up your projector, Lens Shift button

Page 11
In the following cases (for front projection):
LENS SHIFT
FAST
SELECT : ENTER

Setting up your projector (continued)

LENS SHIFT button

To adjust the positions of the projector and the screen, use LENS SHIFT button.

1. Press the LENS SHIFT button.

• The LENS SHIFT menu appears at the center of the screen.

2. Press the S, T, W or X button to move the image position.

• When the T button is pressed, the image moves down.

• When the S button is pressed, the image moves up.

When the X button is pressed, the image moves to the right.

When the W button is pressed, the image moves to the left.

When the ENTER button is pressed while the LENS SHIFT menu is displayed, the shift mode can be switched between FAST and STEP. When FAST is selected, the lens shifts in a large amount with the S, T, W or X button, and it shifts in a small amount when STEP is selected.

When the LENS SHIFT menu is displayed while no video signal is input to the projector, a crosshatch appears on the entire screen.

Be careful not to be caught in the opening in the lens while the lens is moving.

When the lens is vertically shifted by a large amount, color separation may occur.

While the lens shift is working, the screen may flicker.

Adjusting the projection angle

For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the two adjustment feet on the bottom of the projector.

1. Rotate the adjustment feet for fine adjustment.

After using the projector:

2. Put the adjustment feet back into the projedtor by rotating the adjustment feet.

When fine streaks are seen on projected images

Screen

Adjustment feet

This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus a little. (See page 15 or 20 for focus adjustment.)

When projected images are distorted to a trapezoid

When the screen and the projector are not placed perpendicularly to each other, projected images become trapezoidal. If you cannot make the projector and the screen perpendicular to each other by mechanical adjustments, adjust keystone.

To adjust keystone:

Press the KEYSTONE button on the projector or the remote control to display KEYSTONE, and adjust the image by pressing the S or T button (or VOLUME + or - button on the remote control).

Important:

Press the T

Press the S

(or -) button.

(or +) button.

For proper keystone adjustment results, reset the lens to the factory-adjusted position using LENS SHIFT RESET in the INSTALLATION menu before carrying out keystone adjustment. (See page 24.)

When the keystone adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean a projection angle.

The allowable range of the adjustment value in the keystone adjustment varies depending on the installation conditions.

When the keystone adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight lines may bend in images with complicated patterns. They are not due to product malfunctions.

When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input signal.

When the keystone adjustment is performed, the displayed image may be distorted.

Depending on the installation conditions of the projector and the screen, a perfect rectangular image and the proper aspect ratio may not be obtained.

Noise may appear on the screen during the keystone adjustment because of the type of the video signal being projected and the setting values of the keystone adjustment. In such cases, set the keystone adjustment values in the range where the image is displayed without noise.

In the keystone adjustment with the option lens, the proper aspect ratio may not be obtained.

EN-11

Image 11
Contents HD8000 Compliance Notice When using the projector in EuropeContents Important safeguards Do not keep using the damaged projector Important safeguardsPreparing your projector Checking accessoriesInserting the batteries into the remote control Control area Terminal board Preparating your projectorOverview Bottom side Remote controlReception angle Using the remote controlOperational range of the remote control Using the wired remote controlScreen size and projection distance Setting up your projectorSetting up the screen When the aspect ratio of the screen isWhen projected images are distorted to a trapezoid Setting up your projectorAdjusting the projection angle When fine streaks are seen on projected imagesRear projection Front projection, ceiling mountingViewing computer images Connecting the projector to a computerFor audio output connection Plugging the power cordViewing computer images For monitor connectionRemove the lens cap Projecting imagesAV mute When connecting to a notebook computerExample of the setting procedure for external output To stop projectingViewing video images Connecting the projector to video equipmentConnecting to a video player, etc Connection for video equipment having an Hdmi terminal Viewing video imagesProjector + DVD player or Hdtv decoder Connection for video equipment having a DVI-D terminal Plugging in the power cordEN-20 With the Feature menu Volume from the speakerSetting the aspect ratio How to change the settings With the remote controlMenu operation SetupMenu operation How to set the menusAvailable settings in the menus EN-24 EN-25 EN-26 EN-27 To sharpen or soften the projected image Sharpness Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintColor Enhancer Adjusting projected imagesTo adjust the tone of white Color Temp About color temperatureYES How to adjust the computer imageLPF Progressive filter Simple method to adjust the image positionTo adjust the horizontal position To adjust the vertical positionSet the image size Advanced featuresSetting procedure Set the background colorTo enable the password function Advanced featuresPassword function To cancel the password functionTo change the input source of the left or right screen To use the split modeSplit FreezeUp button Mouse remote controlProjector + computer with USB connector OperationAbout PJLink Supervising and controlling by computerProjectorView PJLinkNormal condition IndicatorsProcedure for changing batteries Terminal cover with anti-theft alarm deviceProcedure for setting the anti-theft alarm device Replacing the lamp Interval of lamp replacementTo replace the lamp Reset of the lamp operation timeReplacing the lamp Cleaning of the lens MaintenanceCleaning of the air-filter Cleaning of the projector and the ventilation slotsFor the air-filter white Accessory air-filter unitAttaching the accessory air-filter unit Cleaning the air-filterNo image appears on the screen TroubleshootingImages are not displayed correctly Problem Solution TroubleshootingNo image appears on the screen Problem Solution Kensington Lock Others Problem SolutionSpecifications Replacement part option/not included in the boxXGA85 SpecificationsWithout terminal cover With terminal cover ConnectorsDimension drawings unit mm Real modeMitsubishi Electric Corporation