Mitsumi electronic HD8000 Accessory air-filter unit, Attaching the accessory air-filter unit

Page 42

Accessory air-filter unit

An accessory air-filter unit is supplied with this projector in order to keep dust out more effectively. When using the projector in a dusty place, replace the air filter (filter cover) attached at the factory with this accessory air-filter unit.

•When using the accessory air-filter unit with the projector installed on the floor, provide a clearance of at least 10

mmbetween the filter and the floor using boards or the like as spacers.

•When using the accessory air-filter unit with the projector installed on the ceiling, attach the ceiling mount in such

away as to provide a clearance of at least 10 mm between the filter and the ceiling mount. (Use the accessory spacers and screws, if necessary.)

Attaching the accessory air-filter unit

Before installing this accessory air-filter unit to the projector, be sure to turn off the main power switch and unplug the projector from the outlet.

• Remove the air-filter (filter cover) attached at the factory first. (See page 41.)

1.

Slide the accessory air-filter unit in the direction of the arrow.

 

•

Don’t use any other accessory air-filter units than that designed for

 

 

this projector.

Accessory air-filter unit

Cleaning the air-filter

Warning:

Never use flammable air duster or other materials when cleaning the accessory air-filter unit. Flammable substances may ignite causing fire or breakdown when the lamp is illuminated.

Before cleaning, be sure to turn off the main power switch and unplug the projector from the outlet.

•Clean the air-filter frequently (at least once a month). When dust accumulates on the filter at the air inlet, the temperature inside the projector may rise abnormally high, causing damage to the internal parts and reducing the lifetime of the panel.

•In case of any abnormality including an abnormal rise of the inside temperature, the projector may automatically turn off and go into the standby mode where the light source lamp is turned off in order to protect its internal parts.

1.Remove the accessory air-filter unit from the projector.

•While holding the tab to the inside, pull out the unit in the arrow’s direction.

Accessory air-filter unit

Tab

2. Remove the air-filter from the cover.

Holder

 

(1)

Remove the holder by pushing the tab of the holder on the air-

 

 

filter in the direction of the arrow.

 

(2)

Remove the air-filter (white) and air-filter (gray).

Cover

 

 

3. Clean dirt and dust adhering to the air-filter using a vacuum.

•For the air-filter (white)

If stubborn stains persist, wash the air-filter with water and dry well in the shade.

•For the air-filter (gray)

If stubborn stains persist, wash the air-filter with diluted detergent, rinse with water, and dry well.

4.Attach the air-filter to the cover.

(1) Attach the air-filter (gray) and air-filter (white) to the cover, aligning their notches with that of the cover.

(2) Insert the left tabs of the holder to the cover and push the right tab in the direction of the arrow to attach the cover.

5.Attach the accessory air-filter unit to the projector.

•Slide the accessory air-filter unit in the direction of the arrow.

Air-filter (gray)

Air-filter (white)

Holder

Accessory air-filter unit

EN-42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents HD8000 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Do not keep using the damaged projectorChecking accessories Inserting the batteries into the remote controlPreparing your projector Preparating your projector OverviewControl area Terminal board Remote control Bottom sideUsing the wired remote control Using the remote controlOperational range of the remote control Reception angleWhen the aspect ratio of the screen is Setting up your projectorSetting up the screen Screen size and projection distanceWhen fine streaks are seen on projected images Setting up your projectorAdjusting the projection angle When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesFor monitor connection Plugging the power cordViewing computer images For audio output connectionProjecting images Remove the lens capTo stop projecting When connecting to a notebook computerExample of the setting procedure for external output AV muteConnecting the projector to video equipment Connecting to a video player, etcViewing video images Viewing video images Projector + DVD player or Hdtv decoderConnection for video equipment having an Hdmi terminal Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-20 How to change the settings With the remote control Volume from the speakerSetting the aspect ratio With the Feature menuSetup Menu operationHow to set the menus Available settings in the menusMenu operation EN-24 EN-25 EN-26 EN-27 To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerHow to adjust the computer image YESTo adjust the vertical position Simple method to adjust the image positionTo adjust the horizontal position LPF Progressive filterSet the background color Advanced featuresSetting procedure Set the image sizeTo cancel the password function Advanced featuresPassword function To enable the password functionFreeze To use the split modeSplit To change the input source of the left or right screenOperation Mouse remote controlProjector + computer with USB connector Up buttonPJLink Supervising and controlling by computerProjectorView About PJLinkIndicators Normal conditionTerminal cover with anti-theft alarm device Procedure for setting the anti-theft alarm deviceProcedure for changing batteries Interval of lamp replacement Replacing the lampReset of the lamp operation time Replacing the lampTo replace the lamp Cleaning of the projector and the ventilation slots MaintenanceCleaning of the air-filter Cleaning of the lensCleaning the air-filter Accessory air-filter unitAttaching the accessory air-filter unit For the air-filter whiteTroubleshooting No image appears on the screenTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpecificationsSpecifications XGA85Real mode ConnectorsDimension drawings unit mm Without terminal cover With terminal coverMitsubishi Electric Corporation
Top Page Image Contents