Mitsumi electronic HD8000 user manual Replacing the lamp, To replace the lamp

Page 40

Replacing the lamp (continued)

To replace the lamp:

(a)

(c)

Handle

(c)

(a)

Important:

1.Turn off the main power switch and unplug the power cord.

2.Reverse the projector gently.

3.Loosen the screw (a) using a Phillips screwdriver (+), and remove the lamp cover (b).

4.Loosen the screws (c) using a Phillips screwdriver (+).

5.Pull up the handle.

6.Pull out the lamp box by the handle while holding the

(b)projector.

•Pull the lamp box out of the projector slowly. If it is pulled out quickly, the lamp may break scattering glass fragments.

•Do not spill liquid on the removed lamp box or do not place it near any ﬂammable object or where children can reach to prevent injury or ﬁre.

7.Load a new lamp box securely into the projector in the right orientation.

8.Put the handle back to the original position.

•Make sure that the handle is locked.

9.Tighten up the screws (c) using a Phillips screwdriver (+).

10.Tighten up the screw (a) using a Phillips screwdriver (+) to secure the lamp cover.

Reset of the lamp operation time

11.Plug the power cord into the wall outlet and turn on the main power switch.

12.Hold down the W, X, and POWER buttons on the control panel at the same time about 3 seconds.

•Unless these 3 buttons are held down at the same time, the lamp operation time isn’t reset.

•Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully.

•The projector doesn’t turn on if the lamp cover isn’t attached securely.

•Be sure to reset the lamp operation time whenever you replace the lamp.

•Do not reset the lamp operation time unless you replace the lamp.

•The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.

•Contact your dealer for a new lamp.

Caution:

This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. (For the U.S. only.)

EN-40

Image 40

Contents HD8000 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Do not keep using the damaged projectorInserting the batteries into the remote control Checking accessoriesPreparing your projector Overview Preparating your projectorControl area Terminal board Remote control Bottom sideUsing the remote control Operational range of the remote controlUsing the wired remote control Reception angleSetting up your projector Setting up the screenWhen the aspect ratio of the screen is Screen size and projection distanceSetting up your projector Adjusting the projection angleWhen ﬁne streaks are seen on projected images When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesPlugging the power cord Viewing computer imagesFor monitor connection For audio output connectionProjecting images Remove the lens capWhen connecting to a notebook computer Example of the setting procedure for external outputTo stop projecting AV muteConnecting to a video player, etc Connecting the projector to video equipmentViewing video images Projector + DVD player or Hdtv decoder Viewing video imagesConnection for video equipment having an Hdmi terminal Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-20 Volume from the speaker Setting the aspect ratioHow to change the settings With the remote control With the Feature menuSetup Menu operationAvailable settings in the menus How to set the menusMenu operation EN-24 EN-25 EN-26 EN-27 Adjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessAdjusting projected images To adjust the tone of white Color TempAbout color temperature Color EnhancerHow to adjust the computer image YESSimple method to adjust the image position To adjust the horizontal positionTo adjust the vertical position LPF Progressive ﬁlterAdvanced features Setting procedureSet the background color Set the image sizeAdvanced features Password functionTo cancel the password function To enable the password functionTo use the split mode SplitFreeze To change the input source of the left or right screenMouse remote control Projector + computer with USB connectorOperation Up buttonSupervising and controlling by computer ProjectorViewPJLink About PJLinkIndicators Normal conditionProcedure for setting the anti-theft alarm device Terminal cover with anti-theft alarm deviceProcedure for changing batteries Interval of lamp replacement Replacing the lampReplacing the lamp Reset of the lamp operation timeTo replace the lamp Maintenance Cleaning of the air-ﬁlterCleaning of the projector and the ventilation slots Cleaning of the lensAccessory air-ﬁlter unit Attaching the accessory air-ﬁlter unitCleaning the air-ﬁlter For the air-ﬁlter whiteTroubleshooting No image appears on the screenNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpeciﬁcationsSpeciﬁcations XGA85Connectors Dimension drawings unit mmReal mode Without terminal cover With terminal coverMitsubishi Electric Corporation