Mitsumi electronic HD8000 user manual Preparing your projector, Checking accessories

Page 6

Preparing your projector

Checking accessories

The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in the package.

Cables

 

Mini D-SUB

D-SUB

DVI

 

15-pin

9-pin

 

 

Mini D-SUB

D-SUB

HDMI

 

15-pin

9-pin

 

 

Audio/Video cable

RGB cable for PC

RS-232C cable

DVI-HDMI

(246C381-10)

(246C597-10)

(246C598-10)

conversion cable

 

Used for projector

(242P033-10)

 

 

control by computer.

 

Power supply parts

Power cord (two) (246C483-10, 246C383-20)

Filter parts

Accessory air-filter unit/ accessories (761B522-10)

Remote control parts

LR6 (size-AA) battery (two)

Terminal cover parts

Safety pin (two) (450D057-10)

LR6 (size-AA) battery (two)

Sticker for anti-theft alarm (853C588-10)

Others

• Lens cap (attached

to the projector)

Air-filter

(620D119-10)

CD-ROM

(919C132-60)

• Safety Manual/

Quick Start up

Remote control

(290P136-40)

Terminal cover (with anti-theft alarm device) (750A657-10)

(871D389-60)

Important:

• The attached power cords are to be used exclusively for this product. Never use them for other products.

Inserting the batteries into the remote control

1

1.

Remove the rear lid of the remote control.

2.

Check the polarity (+), (-) of the batteries, and set them

 

3

correctly, inserting their (-) side first.

If the battery is inserted from the (+) side first, inserting the (-) side is difficult because the coil spring end hits on the battery side. If the battery is forced to insert in this

2

way, the outer label of the battery may get ripped and it

may cause a short-circuit and heating.

 

 

3. Attach the rear lid.

Important:

• Use two size-AA batteries (LR6).

• Replace the 2 batteries with new ones when the remote control is slow to operate.

Caution:

Use of a battery of wrong type may cause explosion.

Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

Dispose of used batteries according to your local regulations.

Batteries may explode if misused. Do not recharge, disassemble, or dispose of them in fire.

Be sure to handle the batteries according to the instructions.

Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.

Keep batteries out of reach of children and pets.

Remove the batteries, if the remote control is not used for a long time.

Do not combine a new battery with an old one.

If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

EN-6

Image 6
Contents HD8000 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Do not keep using the damaged projectorChecking accessories Inserting the batteries into the remote controlPreparing your projector Preparating your projector OverviewControl area Terminal board Remote control Bottom sideUsing the wired remote control Using the remote controlOperational range of the remote control Reception angleWhen the aspect ratio of the screen is Setting up your projectorSetting up the screen Screen size and projection distanceWhen fine streaks are seen on projected images Setting up your projectorAdjusting the projection angle When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesFor monitor connection Plugging the power cordViewing computer images For audio output connectionProjecting images Remove the lens capTo stop projecting When connecting to a notebook computerExample of the setting procedure for external output AV muteConnecting the projector to video equipment Connecting to a video player, etcViewing video images Viewing video images Projector + DVD player or Hdtv decoderConnection for video equipment having an Hdmi terminal Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-20 How to change the settings With the remote control Volume from the speakerSetting the aspect ratio With the Feature menuSetup Menu operationHow to set the menus Available settings in the menusMenu operation EN-24 EN-25 EN-26 EN-27 To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerHow to adjust the computer image YESTo adjust the vertical position Simple method to adjust the image positionTo adjust the horizontal position LPF Progressive filterSet the background color Advanced featuresSetting procedure Set the image sizeTo cancel the password function Advanced featuresPassword function To enable the password functionFreeze To use the split modeSplit To change the input source of the left or right screenOperation Mouse remote controlProjector + computer with USB connector Up buttonPJLink Supervising and controlling by computerProjectorView About PJLinkIndicators Normal conditionTerminal cover with anti-theft alarm device Procedure for setting the anti-theft alarm deviceProcedure for changing batteries Interval of lamp replacement Replacing the lampReset of the lamp operation time Replacing the lampTo replace the lamp Cleaning of the projector and the ventilation slots MaintenanceCleaning of the air-filter Cleaning of the lensCleaning the air-filter Accessory air-filter unitAttaching the accessory air-filter unit For the air-filter whiteTroubleshooting No image appears on the screenTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpecificationsSpecifications XGA85Real mode ConnectorsDimension drawings unit mm Without terminal cover With terminal coverMitsubishi Electric Corporation