Mitsumi electronic HD8000 Split, Freeze, To use the split mode, To resume the motion in the image

Page 34

Advanced features (continued)

Split

You can split the screen in two and display a computer image on the left screen and a video image on the right screen.

Left screen

Right screen

To use the split mode:

1.Press the SPLIT button on the remote control.

•The screen is split in two and the left and right screens display the following images:

-Left screen: Image supplied to the last se- lected input source, COMPU- TER1, COMPUTER2, or DVI

-Right screen: Image supplied to the last selected input source, VIDEO or S-VIDEO

•When you press the SPLIT button again, the screen is displayed in the normal mode.

•Also, when you press the MENU button or change the input source, the screen is displayed in the normal mode.

•In the split mode, audio of the left screen is output.

•In the split mode, the picture quality settings of the input source in the normal mode to be displayed on the left screen are reﬂected on the entire screen.

•When no signal is input, a blue screen is displayed.

•When you input an interlace signal to the left screen, the displayed image may shake up and down slightly, but this is not a malfunction.

•When you display 60-Hz and 50-Hz video signals at the same time, motion images may not be displayed properly. In this case, set VERT. SYNC of USER in the SIGNAL menu to OFF for the left screen. (See page 26.)

•When BACK COLOR of the INSTALLATION menu is set to IMAGE, you cannot use the split mode.

To change the input source of the left or right screen:

•To change the input source of the left screen, press the W button on the remote control.

•To change the input source of the right screen, press the X button on the remote control.

Freeze

To stop the motion in the image temporarily (or to display a still image):

Press the FREEZE button on the remote control.

• The image will freeze temporarily.

To resume the motion in the image:

Press the FREEZE button on the remote control again.

Important:

•Do not display a still picture for a long time because the afterimages may persist on the screen. (See page 44.)

EN-34

Image 34

Contents HD8000 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Do not keep using the damaged projectorInserting the batteries into the remote control Checking accessoriesPreparing your projector Overview Preparating your projectorControl area Terminal board Remote control Bottom sideUsing the wired remote control Using the remote controlOperational range of the remote control Reception angleWhen the aspect ratio of the screen is Setting up your projectorSetting up the screen Screen size and projection distanceWhen ﬁne streaks are seen on projected images Setting up your projectorAdjusting the projection angle When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesFor monitor connection Plugging the power cordViewing computer images For audio output connectionProjecting images Remove the lens capTo stop projecting When connecting to a notebook computerExample of the setting procedure for external output AV muteConnecting to a video player, etc Connecting the projector to video equipmentViewing video images Projector + DVD player or Hdtv decoder Viewing video imagesConnection for video equipment having an Hdmi terminal Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-20 How to change the settings With the remote control Volume from the speakerSetting the aspect ratio With the Feature menuSetup Menu operationAvailable settings in the menus How to set the menusMenu operation EN-24 EN-25 EN-26 EN-27 To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerHow to adjust the computer image YESTo adjust the vertical position Simple method to adjust the image positionTo adjust the horizontal position LPF Progressive ﬁlterSet the background color Advanced featuresSetting procedure Set the image sizeTo cancel the password function Advanced featuresPassword function To enable the password functionFreeze To use the split modeSplit To change the input source of the left or right screenOperation Mouse remote controlProjector + computer with USB connector Up buttonPJLink Supervising and controlling by computerProjectorView About PJLinkIndicators Normal conditionProcedure for setting the anti-theft alarm device Terminal cover with anti-theft alarm deviceProcedure for changing batteries Interval of lamp replacement Replacing the lampReplacing the lamp Reset of the lamp operation timeTo replace the lamp Cleaning of the projector and the ventilation slots MaintenanceCleaning of the air-ﬁlter Cleaning of the lensCleaning the air-ﬁlter Accessory air-ﬁlter unitAttaching the accessory air-ﬁlter unit For the air-ﬁlter whiteTroubleshooting No image appears on the screenNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpeciﬁcationsSpeciﬁcations XGA85Real mode ConnectorsDimension drawings unit mm Without terminal cover With terminal coverMitsubishi Electric Corporation