Mitsumi electronic HD8000 user manual Important safeguards

Page 4

Important safeguards

Please read all these instructions regarding your projector and retain them for future reference. Follow all warnings and instructions marked on the projector.

1.Read instructions

All the safety and operating instructions should be read before the appliance is operated.

2.Retain instructions

The safety and operating instructions should be retained for future reference.

3.Warnings

All warnings on the appliance and in the operating instructions should be adhered to.

4.Instructions

All operating instructions must be followed.

5.Cleaning

Unplug this projector from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.

6.Attachments and equipment

Never add any attachments and/or equipment without the approval of the manufacturer as such additions may result in the risk of fire, electric shock or other personal injury.

7.Water and moisture

Do not use this projector near water or in contact with water.

8.Accessories

Do not place this projector on an unstable cart, stand, tripod, bracket or table. Use only with a cart, stand, tripod bracket, or table recommended by the manufacturer or sold with the projector. Any mounting of the appliance should follow

the manufacturer’s instructions and should use a mounting accessory recommended by the manufacturer.

An appliance and cart combination should be moved with care. Quick stops, excessive force and uneven surfaces may cause the appliance and cart combination to overturn.

9.Ventilation

Slots and openings in the cabinet are provided for ventilation, ensuring reliable operation of the projector and to protect it from overheating. Do not block these openings or allow them to be blocked by placing the projector on a bed, sofa, rug, or bookcase. Ensure that there is adequate ventilation and that the manufacturer’s instructions have been adhered to.

10.Power sources

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power, please consult your appliance dealer or local power company.

11.Power-cord protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles, and points where they exit from the appliance. Do not put the power cord under a carpet.

12.Overloading

Do not overload wall outlets and extension cords as this can result in a fire or electric shock.

13.Objects and liquids

Never push objects of any kind through openings of this projector as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

14.Servicing

Do not attempt to service this projector by yourself. Refer all servicing to qualified service personnel.

15.Damage requiring service

Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions:

(a)If the power-supply cord or plug is damaged.

(b)If liquid has been spilled, or objects have fallen into the projector.

(c)If the projector does not operate normally after you follow the operating instructions. Adjust only those controls that are covered by the operating instructions. An improper adjustment of other controls may result in damage and may often require extensive work by a qualified technician to restore the projector to its normal operation.

(d)If the projector has been exposed to rain or water.

(e)If the projector has been dropped or the cabinet has been damaged.

(f)If the projector exhibits a distinct change in performance - this indicates a need for service.

16.Replacement parts

When replacement parts are required, be sure that the service technician has used replacement parts specified by the manufacturer or parts having the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

17.Safety check

Upon completion of any service or repair to this projector, ask the service technician to perform safety checks determining that the projector is in a safe operating condition.

EN-4

Image 4
Contents HD8000 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Do not keep using the damaged projectorInserting the batteries into the remote control Checking accessoriesPreparing your projector Overview Preparating your projectorControl area Terminal board Remote control Bottom sideUsing the remote control Operational range of the remote controlUsing the wired remote control Reception angleSetting up your projector Setting up the screenWhen the aspect ratio of the screen is Screen size and projection distanceSetting up your projector Adjusting the projection angleWhen fine streaks are seen on projected images When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesPlugging the power cord Viewing computer imagesFor monitor connection For audio output connectionProjecting images Remove the lens capWhen connecting to a notebook computer Example of the setting procedure for external outputTo stop projecting AV muteConnecting to a video player, etc Connecting the projector to video equipmentViewing video images Projector + DVD player or Hdtv decoder Viewing video imagesConnection for video equipment having an Hdmi terminal Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-20 Volume from the speaker Setting the aspect ratioHow to change the settings With the remote control With the Feature menuSetup Menu operationAvailable settings in the menus How to set the menusMenu operation EN-24 EN-25 EN-26 EN-27 Adjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessAdjusting projected images To adjust the tone of white Color TempAbout color temperature Color EnhancerHow to adjust the computer image YESSimple method to adjust the image position To adjust the horizontal positionTo adjust the vertical position LPF Progressive filterAdvanced features Setting procedureSet the background color Set the image sizeAdvanced features Password functionTo cancel the password function To enable the password functionTo use the split mode SplitFreeze To change the input source of the left or right screenMouse remote control Projector + computer with USB connectorOperation Up buttonSupervising and controlling by computer ProjectorViewPJLink About PJLinkIndicators Normal conditionProcedure for setting the anti-theft alarm device Terminal cover with anti-theft alarm deviceProcedure for changing batteries Interval of lamp replacement Replacing the lampReplacing the lamp Reset of the lamp operation timeTo replace the lamp Maintenance Cleaning of the air-filterCleaning of the projector and the ventilation slots Cleaning of the lensAccessory air-filter unit Attaching the accessory air-filter unitCleaning the air-filter For the air-filter whiteTroubleshooting No image appears on the screenNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpecificationsSpecifications XGA85Connectors Dimension drawings unit mmReal mode Without terminal cover With terminal coverMitsubishi Electric Corporation